The Tamil Nadu Factories Rules, 1950
Arrangement of Rules
G.O. No. 1041 of 1950 · Tamil Nadu · 68 chapters and schedules, 167 rules
Chapter V
WELFARE
62.Washing facilities
Rule Prescribed under sub-section (2) of section 42
This rule shall come into force, in respect of any class or description of factories, on such dates as the State Government may, by notification in the Official Gazette, appoint in this behalf.
There shall be provided and maintained in every factory for the use of employed persons adequate and suitable facilities for washing which shall include soap and nail brushes or other suitable means of cleaning and the facilities shall be conveniently accessible and shall be kept in a clean and orderly condition.
Without prejudice to the generality of the foregoing provisions, the washing facilities shall include –
(a) a trough with taps or jets at intervals of not less than 61 centimeters, or
(b) wash-basins with taps attached thereto, or
(c) taps on stand-pipes, or
(d) showers controlled by taps, or
(e) circular troughs of the fountain type, provided that the Inspector may, having regard to the needs and habits of the workers, fix the proportion in which the aforementioned types of facilities shall be installed,
(f) or such other washing facilities as the Inspector may consider sufficient and suitable in the circumstances of each case.
(a) Every trough and basin shall have a smooth, impervious surface and shall be fitted with a waste pipe and plug.
(b) The floor or ground under and in the immediate vicinity of every trough, tap, jet, wash-basin, stand-pipe and shower shall be so laid or finished as to provide a smooth, impervious surface and shall be adequately drained.
For persons whose work involves contact with any injurious or noxious substance there shall be at least one tap for every fifteen persons; and for persons whose work does not involve such contact the number of taps shall be as follows: Number of workers Number of taps Up to 20 1 21 to 35 2 36 to 50 3 51 to 150 4 151 to 200 5 5 plus one tap for every 50 or fraction of Exceeding 200 but not exceeding 500 50 11 plus one tap for every 100 or fraction Exceeding 500 of 100
If female workers are employed, separate washing facilities shall be provided and so enclosed or screened that the interiors are not visible from any place where persons of the other sex work or pass. The entrance to such facilities shall bear conspicuous notice in the language understood by the majority of the workers "For Women only" and shall also be indicated pictorially.
The water-supply to the washing facilities shall be capable of yielding at least 27.3 liters a day for each person employed in the factory and shall be from a source approved in writing by the Health Officer:
Provided that where the Chief Inspector is satisfied that such an yield is not practicable he may by certificate in writing permit the supply of a smaller quantity not being less than 4.5 liters per day for every person employed in the factory.
62.A All classes of factories mentioned in the schedule annexed hereto shall provide facilities for keeping clothing not worn during working hours and for the drying of wet clothing. Such facilities shall include the provision of separate rooms, bags, lockers or other arrangements approved by the Chief Inspector of Factories. THE SCHEDULE Glass Works Engineering Works Iron and Steel Works Oil Mills Chemical Works Automobile Workshop Dyeing Works 137 [Tea Factories] 138
62-B.Health and Safety Policy
The occupier of every factory, except as provided for in sub-role (2), shall prepare a written statement of his policy in respect of health and safety of workers at work.
All factories,
(a) covered under section 2 (m) (i) but employing less than fifty workers;
(b) covered under section 2 (m) (ii) but employing less than one hundred workers; are exempted from requirements of sub rule (1):
Provided that they are not covered under the First Schedule under section 2 (cb) or carrying out processes or operations declared to be dangerous under section 87 of the Act.
Notwithstanding anything contained in sub-rule (2), the Chief Inspector may require the occupiers of any of the factories or class or description of factories to comply with the requirements of sub-rule (1), if, in his opinion, it is expedient to do so.
The Health and Safety Policy should contain or deal with:
(a) declared intention and commitment of the top Management to health, safety and environment and compliance with all the relevant statutory requirements;
(b) organizational set up to carry out the declared policy clearly assigning the responsibility at different levels and;
(c) arrangements for making the policy effective.
In particular, the policy should specify the following
(a) arrangements for involving the workers;
(b) intention of taking into account the health and safety performance of individuals at different levels while considering their career advancement;
(c) fixing the responsibility of the contractors, sub-contractors, transporters and other agencies entering the premises;
(d) providing a resume of health and safety performance of the factory in its Annual Report;
(e) relevant techniques and methods, such as safety audits and risk assessment for periodical assessment of the status on health, safety and environment and taking all the remedial measures;
(f) stating its intentions to integrate health and safety, in all decisions, including those dealing with purchase of plant, equipment machinery and material as well as selection and placement of personnel;
(g) arrangements for informing, educating and training and retaining its own employees at different levels and the public, wherever required;
A copy of the declared Health and Safety Policy signed by the occupier shall be made available to the Inspector having jurisdiction over the factory and to the Chief Inspector;
The policy shall be made widely known by
(a) making copies available to all workers including contract workers, apprentices, transport workers, suppliers, etc.;
(b) displaying copies of the policy at conspicuous places; and
(c) any other means of communication; in a language understood by majority of workers.
The occupier shall revise the Safety Policy as often as may be appropriate, but it shall necessarily be revised under the following Circumstances:
(a) Whenever any expansion or modification having implications on safety and health of persons at work is made; or
(b) Whenever new substance(s) or articles are introduced in the manufacturing process having implications on health and safety of per-sons exposed to such substances;
62-C.Collection and Development and Dissemination of Information
The occupier of every factory carrying an a hazardous process shall arrange to obtain development information in the form of Material Safety Data Sheet (MSDS) in respect of every hazardous substance or material handled in the manufacture, transportation and storage in the factory. It shall be accessible upon request to a worker for reference.
(a) Every such material Safety Data Sheet shall include the following information,
(i) The identify used on the label;
(ii) Hazardous ingredients of the substance;
(iii) Physical and chemical characteristics of the hazardous substance;
(iv) The physical hazards of the hazardous substance, including the potential for fire explosion and reactivity;
(v) The health hazards of the hazardous substance, including signs and symptoms of exposure, and any medical conditions which are generally recognised as being aggravated by exposure to the substance;
(vi) The primary route(s) of entry;
(vii) The permissible limits of exposure prescribed in the Second Schedule under section 41-F of the Act, and in respect of a Chemical not covered by the said Schedule, any exposure limit used or recommended by the manufacturer, importer or occupier:
(viii) Any generally applicable precautions for safe handling and use of the hazardous substance, which arc known, including appropriate hygienic practices, protective measures during repairs and maintenance of contaminated equipment, procedures for clean-up of spills and leaks:
(ix) Any generally applicable control measures, such as appropriate engineering controls, work practices. or use of personal protective equipment;
(x) Emergency and first aid procedures;
(xi) The date of preparation of the Material Safety Data Sheet, or the last change to it; and
(xii) The name, address and telephone number of the manufacturer, importer, occupier or other responsible party preparing or distributing the Material Safety Data Sheet who can provide additional information on the hazardous substance and appropriate emergency procedures, if necessary.
(b) The occupier who (sic.) obtaining or developing a Material Safety Data Sheet in respect of hazardous substance shall ensure that the information recorded accurately reflects the scientific evidence used in making the hazard determination. If he be-comes newly aware of any significant information regarding the hazards of a substance, or ways to protect against the hazards, this new information shall be added to the Material Safety Data Sheet as soon as practicable.
(c) An example of such Material Safety Data Sheet is given in the Schedule to this rule.
Labeling- Every container of a hazardous substance shall be clearly labeled or marked to identify:
(a) the contents of the container:
(b) the name and address of the manufacturer or importer of the hazardous substances;
(c) the physical and health hazards; and
(d) the recommended personal protective equipment needed to work safely with the hazardous substance. 139 [THE SCHEDULE MATERIAL SAFETY DATA SHEET 1. IDENTITY OF MATERIALS Product Name Chemical Designation Trade Name Synonyms CAS UN Formula Label Category Number Number Shipping Name/Codes/Label HAZCHEM Code Regulated Identification Hazardous Waste Identification Number Hazardous Ingredients CAS Number 1. 2. 3. 4. 2. PHYSICAL AND CHEMICAL PROPERTIES Physical State: (Gas, Liquid- Vapour pressure at 35 Boiling point in degree C.Solid-) degree C--mm Hg. Melting/Freezing point in Evaporation rate at 30 Appearance degree C degree C Solubility in Water at 30 Odour Vapour Density (air-I) degree C Others (Corrosivity) etc Specific Gravity (Water-1) PH 3. FIRE AND EXPLOSIVE HAZARDS DATA Auto ignition Flash Point (deg.) LEL % Temperature degree C C Explosion/Flammability Flash Point (deg.) TDC Flammability UEL% C (Classification) 4. REACTIVE HAZARDS Impact (Hazardous Combustion products) Stability to Static Discharge (Hazardous Decomposition product) Reactivity (Conditions to avoid) Hazardous May/May not occur (Conditions to avoid) Polymerization Incompatibility (Materials to avoid) 5. HEALTH HAZARDS DATA Routes of Entry: (Inhalation, skin, mucous membranes, eye contact and ingestion) Effects of Exposure/Symptoms (Orally or LD 50 (in rat) LC 50 (in rat) (mg/1) percutaneous 4/hours (mg/kg body weight) absorption) Threshold PPM. Odor PPM. Limit Value Mg/cu m Threshold Mg/cu. M
(TLV) of ACGIH Emergency Treatment:
6. HAZARD SPECIFICATION NFPA Signal Health Flammability Stability Special Hazard Known Hazards: Water Reactive Combustible Liquid Irritant Material Flammable Material Oxidizer Sensitizer Pyrophoric Material Organic Peroxide Carcinogen Explosive Material Corrosive Material Mutagen Other Unstable Material Compressed Gas (Specify) 7. SAFE USAGE DATA Ventilation General/Mechanical Local Exhaust Protective Equipment Required Eyes (Specify) Respiratory (Specify) Gloves (Specify) Clothing (Specify) Others (Specify) Precautions Handling & Storage Others (speedy) 8. EMERGENCY RESPONSE DATA Fire Fire Extinguishing Media Special procedures Unusual Hazards Exposure First Aid Measures (inhalation, skin, eye contact and ingestion) Spills Step to be taken Waste Disposal Method 9. ADDITIONAL INFORMATION 10. SOURCES USED:
Reference to books, journals, etc.
11. MANUFACTURERS/SUPPLIER DATA Firm's Name Standard packing Mailing Address Telephone Number Telex Number Others Telegraphic Address Contact person in Emergency Others Emergency Telephone in Transit Areas Acronyms- and Glossary, of terms:
CAS: Chemical Abstract Service Registration Number.
UN Number: United Nations Number HAZCHEM CODE: Emergency Action Code (EAC). allocated by the Joint Comminute of Fire Bripde Operations, UK.
TDG Flammability: Transport of Dangerous Goods --Flammability Classification by United Nations.
NFPA: National Fire Protection Association, USA. LD 50 and LC 50 represent the dose in mg/kg of body weight and the concentration in mg/1 for 4 hours having lethal effect on 50% of the animals (rats) treated.
PEL: Permissible Exposure Limit as laid down in the Statutes.
TLV: Threshold Limit Value as laid down by the American Conference of Governmental Industrial Hygienists. (ACGIH), USA.
STE L: Short Term Exposure Limit as laid down in the statutes or by the ACGIH.
GUIDELINES: All efforts should be made to fill in all the columns. No column should be left blank. In case certain information is not applicable or available. N/APP or N/AV sign may be used.
62-D.Disclosure of information to workers
The Occupier of a factory carrying on a hazardous process shall supply to all workers the following information in relation to handling of hazardous materials or substances in the manufacture transportation, storage and other processes
(a) Requirements of Sections 41-B, 41-C and 4I-H of the Act:
(b) A list of hazardous processes carried on in the factory;
(c) Location and availability of all Material Safety Data Sheets as per Rule 62-B;
(d) Physical and health hazards arising from the exposure to or handling of substances:
(e) Measures taken by the occupier to ensure safety and control of physical and health hazards;
(f) Measures to be taken by the workers to ensure safe handling, storage and transportation of hazardous substances;
(g) Personal Protective Equipment required to be used by workers employed in hazardous process or dangerous operations:
(h) Meaning of various labels and markings used on the containers of hazardous substances as provided under Rule 62-B;
(i) Signs and symptoms likely to be manifested on exposure to hazardous substances and to whom to report;
(j) Measures to be taken by the workers in case of any spillage or leakage of a hazardous substance;
(k) Role of workers vis-a-vis the emergency plan of the factory. in particular the evacuation procedures; and
(1) Any other information considered necessary by the occupier to ensure safety and health of workers.
(2) The information required by sub-rule (1) shall be compiled and made known to workers individually through supply of booklets or leaflets and display of cautionary notices at the work places.
(3) The booklets, leaflets and the cautionary notices displayed in the factory shall be in the language understood by the majority of the workers, and also explain to them.
(4) The Chief Inspector may direct the Occupier to supply further information to the workers as deemed necessary.
[Rules 62E to 62G omitted by G.O. Ms. No. 222, Labour and Employment, dated the 21st November, 1995]
62-H.Disclosure of information to the Chief Inspector
140
[The Occupier of every factory carrying on "hazardous process" shall furnish in writing. to the Chief Inspector a copy of all the information furnished to the workers]
A copy of compilation of Material Safety Data Sheets in respect of hazardous substances used, produced or stored in the factory shall he furnished to the Chief Inspector and the local Inspector.
The Occupier shall also furnish any other information asked for by the Chief Inspector from time to time for the purpose of this Act and rules made thereunder. st [Rules 62-I and 62J omitted by G.O. Ms. No. 222, dated the 1 November, 1995]
62-K.Information on Industrial Wastes
[The information furnished under rules 62-D and 62-H shall include the quantity of the solid and liquid wastes generated per day, their characteristics and the method of treatment such as incineration of solid wastes, chemical and biological treatment of liquid wastes, and arrangements for their final disposal.]
It shall also include information on the quality and quantity of gaseous waste discharged through the stacks or other openings and arrangements such as provision of scrubbers, cyclone separators electrostatic precipitators or similar such arrangement made for controlling pollution of the environment.
The Occupier shall also furnish the information prescribed in the sub-rules (I) and (2) to the State Pollution Control Board.
62-L.Review of the information furnished to workers, etc
141
[The Occupier shall review once in every calendar year and modify, if necessary, the information furnished under rules 62-D and 62-H to the workers and the Chief Inspector.]
In the event of any change in the process or operations or methods of work or when any new substance is introduced in the process or in the event of a serious accident taking place, the information so furnished shall be reviewed and modified to the extent necessary.
62-M.Confidentiality of information
The Occupier of a factory carrying on an "hazardous process" shall disclose all information needed for protecting the safety and health of the workers to
(a) his workers; and
(b) Chief Inspector as required under rules 62-D and 62-H. If the Occupier is of the opinion that the disclosure of details regarding the process and formulations will adversely affect his business interests, he may make representation to the Chief Inspector stating the reasons for withholding such information. The Chief Inspector shall give an opportunity to the Occupier of being heard and pass an order on the representation. An Occupier aggrieved by an order of the Chief Inspector may prefer an appeal before the State Government within a period of thirty days. The State Government shall give an opportunity to the Occupier of being heard and pass an order. The order of the State Government shall be final.]
62-N.Medical Examination
Workers employed in a "hazardous process" shall be medically examined by a qualified medical practitioner hereinafter referred to as Factory Medical Officer in the following manner:
(a) Once before employment, to ascertain the physical fitness of the person to do the particular job:
(b) Once in a period of six months, to ascertain the health status of all the workers in respect of occupational health hazards to which they are exposed; and in cases where in the opinion of the Factory Medical Officer it is necessary to do so at a shorter interval in respect of any workers.
(c) The details of pre-employment and periodical examinations carried out as aforesaid shall be recorded in the Health Registers in Forms 39 and 17 respectively.
No person shall be employed for the first time without a Certificate of Fitness in Form 27 granted by the Factory Medical Officer. If the Factory Medical Officer declares a person unfit for being employed in any process covered under sub-rule (I), such a person shall have the right to appeal to the Inspector who shall refer the matter to the Certifying Surgeon whose opinion shall be final in this regard. If the Inspector is also a Certifying Surgeon, he may dispose of the application himself
Any findings of the Factory Medical Officer revealing any abnormality or unsuitability of any person employed in the process shall immediately be reported to the Certifying Surgeon who shall in turn, examine the concerned worker and communicate his findings to the occupier within thirty days. If the Certifying Surgeon is of the opinion that the workers examined is required to be taken away from the process for health protection, he will direct the occupier accordingly, who shall not employ the said worker in the same process. However, the worker so taken away shall be provided with alternate placement unless he is in the opinion of the Certifying Surgeon, fully incapacitated in which case the worker affected shall he suitably rehabilitated.
A Certifying Surgeon on his own motion or on a reference from an Inspector may conduct medical examination of a worker to ascertain the suitability of his employment in a hazardous process or for ascertaining his health status. The opinion of the Certifying Surgeon in such a case shall be final. The fee required for this medical examination shall be paid by the occupier.
The worker taken away from employment in any process under sub-rule (2) may be employed again in the same process only after obtaining the Fitness Certificate from the Certifying Surgeon and after making entries to that effect in the Health Register.
The worker required to undergo medical examination under these rules and for any medical survey conducted by or on behalf of the Central or the State Government shall not refuse to undergo such medical examination.
62-O.Occupational Health Centers
In respect of any factory carrying on "Hazardous process" there shall be provided and maintained in good order an Occupational Health Centre with the services and facilities as per scale laid down hereunder:
(a) For factories employing up to fifty workers
(i) the services of a Factory Medical Officer on retainership basis, in his clinic to be notified by the occupier. He will carry out the pre- 142 employment and periodical medical examination as stipulated in [rule 62-N] and render medical assistance during any emergency;
(ii) a minimum of five persons trained in first-aid procedure amongst whom at least one shall always be available during the working period;
(iii) a fully equipped first aid box.
(b) For factories employing fifty-one to two hundred workers
(i) shall have an occupational health centre. It is suggested that it shall have a room with a floor area of fifteen square meters with floors and walls made of smooth and imperious surface and adequate illumination and ventilation. It is suggested to have the equipments given in the Schedule annexed to this rule;
(ii) a part-time Factory Medical Officer shall be in overall charge of the centre who shall visit the factory atleast twice in a week and whose services shall be readily available during medical emergencies;
(iii) one qualified and trained dresser-cum-compounder on duty throughout the working period;
(iv) a fully equipped first-aid box in all the departments.
(c) For factories employing above two hundred workers
(i) one full time Factory Medical Officer for factories employing up to five hundred workers and one more Medical Officer for every additional thousand workers or part thereof;
(ii) shall have an Occupational Health Centre. It is suggested that it shall have two rooms with a floor area of fifteen sq. meters with floors and walls made of smooth and impervious surface and adequate illumination and ventilation. It is suggested to have the equipments given in the Schedule annexed to this rule;
(iii) there shall be one nurse, one dresser-cum-compounder and one sweeper-cum-ward boy throughout the working period:
(iv) the Occupational Health Centre shall be suitably equipped to manage medical emergencies;
The Factory Medical Officer required to be appointed under sub-rule (I) shall have qualifications included in the Schedules to the Indian Medical Degrees Act, 1916 (Central Act VII of 1916) or in the Schedules to the Indian Medical Council Act. 1956 (Central Act 102 of 1956) and possess a Certificate of Training in Industrial Health of minimum three months duration recognized by the State Government
Provided that
(i) a person possessing a Diploma in Industrial Health or equivalent shall not be required to possess the certificate of training as aforesaid;
(ii) the Chief Inspector may subject to such conditions as he may specify, grant exemption from the requirement of this sub-rule, if in his opinion a suitable person possessing the necessary qualification is not available for appointment:
(iii) in case of a person who has been working as a Factory Medical Officer for a period of not less than three years on the date of commencement of this rule, the Chief Inspector may, subject to the condition that the said person shall obtain the aforesaid certificate of training within a period of three years, relax the qualification.
The syllabus of the course leading to the above certificate, and the organisations conducting the Course shall be approved by the Directorate-General of Factory Advice Service and Labour Institutes or the State Government in accordance with the guidelines issued by the DGFASLI.
Within one month of the appointment of a Factory Medical Officer, the occupier of the factory shall furnish to the Chief Inspector the following particulars
(a) Name and address of the Factory Medical Officer;
(b) Qualifications;
(c) Experience, if any; and
(d) the sub-rule under which appointed. THE SCHEDULE SUGGESTIVE LIST OF EQUIPMENT FOR OCCUPATIONAL HEALTH CENTRE IN FACTORIES 1. A glazed sink with hot and cold water always available.
2. A table with a smooth top at least 180 cm x 105 cm.
3. Means for sterilizing instruments.
4. A couch.
5. Two buckets or containers with close fitting lids.
6. A kettle and spirit stove or other suitable means of boiling water.
7. One bottle of spirit ammonia aromatics (120 ml.) 8. Two medium size sponges.
9. Two "Kidney" trays.
10. Four cakes of toilet, preferably antiseptic soap.
11. Two glass tumblers and two wine glasses.
12. Two clinical thermometers.
13. Two teaspoons.
14. Two graduated (120 ml.) measuring glasses.
15. One wash bottle (1000 cc) for washing eyes.
16. One bottle (one liter) carbolic lotion 1 in 20.
17. Three chairs 18. One Screen 19. One electric hand-torch.
20. An adequate supply of tetanus toxoid.
21. Coramine liquid (60 ml.) 22. Tablets -- antihistaminic antispasmodic (25 each.) 23. Syringes with needles - 2 cc., 5 cc. and 10 cc.
24. Two needle holders, big and small.
25. Suturing needles and materials.
26. One dissecting forceps.
27. One dress in forceps.
28. One scalpel.
29. One stethoscope.
30. Rubber bandage -- pressure bandage.
31. Oxygen cylinder with necessary attachments.
32. One Blood Pressure Apparatus.
33. One Patellar Hammer.
34. One Peak-Flow meter for lung function measurement.
35. One stomach washout.
36. Any other equipment recommended by the Factory Medical Officer according to specific need relating to manufacturing process.
37. In addition
(1) For Factories employing fifty one to two hundred 1. Four plain wooden splints 900 mm x 100 mm x 6 mm: 2. Four plain wooden splints 350 mm x 75 mm x 6 mm; 3. Two plain wooden splints 250 mm x 50 mm x 12 mm; 4. 0ne pair artery forceps; 5. Injections -- morphia, pethidine, atropine, adrenaline, coramine, Novocain (2 each); 6. One surgical scissor;
(2) For Factories employing above two hundred workers 1. Eight plain wooden splints 900 mm x 100 mm x 6 mm; 2. Eight plain wooden splints 350 mm x 75 mm x 6 mm; 3. Four plain wooden splints 250 mm x 50 mm x 12 mm: 4. Two pairs artery forceps; 5. Injections Morphia, pethadine, atropine, adrenaline. ceramine, novacain (4 each): 6. Two Surgical scissors.
62-P.Ambulance Van
In any factory carrying on "hazardous process" there shall be provided and maintained in good condition, a suitably constructed ambulance van equipped with item as per sub-rule (2) and manned by a full-time Driver-cum-Mechanic and a Helper trained in first-aid for the purpose of transportation of serious cases of accidents or sickness. The ambulance van shall not be used for any purpose other than the purpose stipulated herein and will normally be stationed at or near to the Occupational Health Centre:
Provided that a factory employing less than two hundred workers, may make arrangements for procuring such facility at short notice from a nearby hospital or other places to meet any emergency.
It is suggested that the ambulance may have the following equipments:
(a) General: A wheeled stretcher with folding and adjusting devices with the head of the stretcher capable of being tilted upward; Fixed suction unit with equipment; Fixed oxygen supply with equipment; Pillow with case; Sheets; Blankets Towels; Emesis bags; Bed pan; Urinal: Glass:
(b) Safety equipment: Flares with life of thirty minutes; Flood lights; Flash lights; -- Fire Extinguisher dry powder type; Insulated gauntlets;
(c) Emergency Care Equipment
(i) Resuscitation --Portable suction unit; portable oxygen units: Bag; Valve; Mask; and operated artificial ventilation unit; Airways; Mouthgags; Trachcctomy adapters; Short spine board; I.V. Fluids with administration unit; B.P. Manometer -- Cup; Stethoscope;
(ii) Immobilization: Long and short padded boards; Wire ladder splints: Triangular bondage -- Long and short spine boards;
(iii) Dressings: Gauze pads -- 4 x 4; — Universal dressing 10 x 36; Roll of aluminum foils; -- soft roller bandages 6 x 5" yards; Adhesive tape in 3 " roll; Safety pins; Bandage Sheets; Burn sheet;
(iv) Poisoning: Syrup of Ipecac; Activated charcoal pre-packeted in dozes; Snake bite kit; Drinking Water;
(v) Emergency Medicines --As per requirement (under the advice of Medical Officer only)
62-Q.Decontamination facilities
In every factory, carrying out hazardous process the following provisions shall be made to meet emergency:
(a) Fully equipped first-aid box;
(b) readily accessible means of water for washing by workers as well as for drenching the clothing of workers who have been contaminated with hazardous and corrosive substance; and such means shall be as per the scale shown in the Table below:-- THE TABLE Number of Persons employed at any time Number of drenching showers
(1) (2)
(i) Upton 50 workers 2 2 + I for every additional 50 or
(ii) Between 51 to 200 workers part thereof. 5 + 1 for every additional 100 or
(iii) Between 201 to 500 workers pan thereof 8 +1 for every additional 200 or
(iv) 501 workers and above part thereof
(c) A sufficient number of eye wash bottles filled with distilled water of suitable liquid kept in boxes or cup-boards conveniently situated and clearly indicated by distinctive sign which shall be visible at all times
62-R.Making available Health Records to Workers
The Occupier of every factory carrying out an "hazardous process" shall make accessible the health records including the record of worker's exposure to hazardous process or, as the case may be, the medical records of any worker for his perusal under the following conditions:
(a) Once in every six months or immediately after the Medical examination whichever is earlier:
(b) If the Factory Medical Officer or the Certifying Surgeon as the case may be is of the opinion that the worker has manifested signs and symptoms of any notifiable disease as specified in the Third Schedule of the Act;
(c) If the worker leaves the employment;
(d) If any one of the following authorities so direct- An inspector notified under the Act; District Health Officer; The Commissioner of Workmen's Compensation: The Director General, Employees' State Insurance Corporation: The Director, Employees' State Insurance Corporation (Medical Benefits); and The Director-General, Factory Advice Service and Labour Institutes.
A copy of the up to-date health records including the records of worker's exposure to hazardous process or as the case may be, the medical records shall be supplied to the worker, on receipt of an application from him. X-ray plates and other medical diagnostic reports may also be made available for reference to his medical practitioner.
62-S.Qualifications, etc., of Supervisors
All persons who are required to supervise the handling of hazardous substances shall possess the following qualifications and experience:
(a)
(i) A degree in Chemistry or Diploma in Chemical Engineering or Technology with five years experience; or
(ii) A Master's Degree in Chemistry or a Degree in Chemical Engineering or Technology with two years experience.
The experience stipulated above shall be in process operation and maintenance in the Chemical Industry.
(b) Chief Inspector may require the supervisor to undergo training in Health and Safety.
The syllabus and duration of the above training and the organisations conducting the training shall be approved by the Director-General. Factory Advice Service and Labour Institutes or the State Government in accordance with the guidelines issued by the Director-General; Factory Advice Service and Labour Institutes.
62-T.Issue of guidelines
For the purpose of compliance with the requirements of sub-sections (1), (4) and (7) of Section 41-B and Section 41-3 (sic.) of the Act, the Chief Inspector may if deemed necessary, issue guidelines from time to time to the occupiers of factories carrying one 'hazardous process'. Such guidelines may be based on National Standards Codes of Practices or recommendations of International Bodies such as International Labour Organization and World Health Organization.
63.First-aid Appliances
In every factory there shall be provided and maintained by regular replenishment first aid 143 boxes or cupboard/s distinctively marked with a red cross on a white background [and it is suggested that the first aid boxes or cupboards are equipped] with the contents as per the appropriate scale specified in the following Table for the corresponding class of Factories A. B or C. as indicated below: Class – A (i) All factories under section 85 (i) of the Act, and
(ii) Factories under section 2 (m) (ii) of the Act, employing up to fifty workers Class – B (i) Factories under section 2 (m) (i) of the Act employing up to fifty workers Class - C (i) Factories under section 2 (m) (i) or 2 (m) (ii) of the Act employing more than fifty workers THE TABLE (Specifying the scale of contents with which each first-aid box or cupboard is to be equipped) Quantity or number applicable to Factories in Sl.No Contents Class A Class B Class C
(1) (2) (3) (4) (5) 1 Copy of First-aid leaflet issued by 1 1 1 the Directorate-General of Factory Advice Service and Labour Institutes, Government of India. Bombay 2 Scissors 1 1 1 3 Snake-bite Iancet 1 1 1 4 100 100 100 Tablet (each of 5 grains of aspirin or any other analgesic) Tablets Tablets Tablets 5 Bottle of Potassium Permanganate 30 ml. 30 ml. 30 ml. crystals 6 Bottle of Salvolatile having the dose 30 ml. 60 ml. 120 ml. and mode of administration indicated on the label 7 Bottle of Contrimide solution (1%) 60 ml. 120 ml. 200 ml. or a suitable antiseptic solution 8 Bottle of Mercurochrome solution 60 ml. 120 ml. 200 ml. (2%) in water 9 15 gm. packet of sterilized cotton 3 6 12 wool 10 Adhesive Plaster (2 cm. x 1 m.) 1 roll 2 rolls 2 rolls 11 Adhesive Plaster (6 cm. x 1 m.) - - 1 roll 12 Small size sterilized dressing or 6 12 24 adhesive wound dressing approved by the Chief Inspector 13 Medium size sterilized dressing or 3 6 12 adhesive wound dressing approved by the Chief Inspector 14 Large size sterilized dressing or 3 6 12 adhesive wound dressing approved by the Chief Inspector 15 Large size sterilized burn dressing 3 6 12 16 Sterilized eye pad in a sealed packet 6 8 12 17 Polythene wash bottle (1/2 liter or 1 1 1 500 cc.) for washing eyes 18 Tourniquet - 1 1 19 Safety pins - 1 Dozen 1 Dozen 20 Roller bandage 5 cm. wide - - 12 21 Roller bandage 10 cm. wide - - 12 22 Triangular bandage - - 6 23 Plain wooden splint 353 mm. x 75 - - 6 mm. X 6 mm 24 Plain wooden splint 900 mm. x 100 - - 6 mm. x 6 mm 25 Plain wooden splint 250 mm. x 50 - - 3 mm. x 12 mm 26 Kidney tray - - 1 144 [Provided that each first-aid box or cupboard shall also contain such other equipment or medicine as the Chief Inspector may deem essential and direct in writing, from time to time:
Provided further that in a factory where a properly equipped ambulance room or dispensary is provided and maintained under rule 64 or if dispensary or hospital is available within one kilometer of the precincts of a factory and such arrangements are made by the Occupier as to ensure the immediate treatment therein of all injuries sustained by a worker within the factory, the Chief Inspector may by an order in writing, relax the requirements of this rule, subject to such conditions as he may specify in that order.]
63-A.Notice regarding first-aid
In every factory, a prominent notice containing the following particulars shall be displayed at some conspicuous and convenient place at or near the main entrance to the factory
(a) the location's of the first-aid box/es or cupboard's in the factory;
(b) the name and designation of the responsible person working within the precincts of the factory who is trained in first-aid treatment and who is separately in charge of each of the above first-aid box/es or cupboard's;
(c) the work-room or place where each such person shall be available during the working hours of the factory; and
(d) the name of the nearest hospital and its telephone number.
Copies of the above notice shall also be displayed at a conspicuous place near each first- aid box or cupboard.
145
63-B.First-aid
Persons who are in charge of first-aid box shall be persons who possess the certificate granted by the Saint John's Ambulance Association for rendering first-aid.]
64.Ambulance room
The ambulance room shall be separately situated from the factory premises. It shall be kept open when any work is being carried on in the factory and shall be used only for the purposes of first-aid treatment and rest. It shall have a floor area of at least 24 square meters and shall be adequately ventilated and lighted by natural and 146 artificial means. The floor and walls shall be smooth, bard and impervious. [There shall be attached to it at least one latrine and urinal of sanitary type].
An adequate supply of wholesome drinking water shall be provided in the ambulance room which shall also contain at least
(i) One screen;
(ii) A table with a smooth top at least 180 cm. x 105 cm.;
(iii) Three chairs;
(iv) A couch;
(v) Two stretchers;
(vi) A glazed sink with hot and cold water always available;
(vii) Two buckets or containers with close fitting lids;
(viii) A kettle and spirit stove or other suitable means of boiling water;
(ix) Means for sterilizing instrument;
(x) Two rubber hot water bags:
(xi) Six woolen blankets;
(xii) Six hand towels;
(xiii) Four cakes of antiseptic soap;
(xiv) Two medium size sponges;
(xv) A stethoscope:
(xvi) Two clinical thermometers;
(xvii) One electric hand torch;
(xviii) Four kidney trays;
(xix) Two glass tumblers;
(xx) Two wine glasses;
(xxi) Two graduated measuring glasses (120 ml.);
(xxii) Two mini-measuring glasses;
(xxiii) Two teaspoons;
(xxiv) One wash bottle (1,000 cc.) for washing eyes:
(xxv) Three surgical scissors;
(xxvi) Three pairs of artery forceps;
(xxvii) Three dissecting forceps;
(xxviii) Three dressing forceps;
(xxix) Three scalpels;
(xxx) Needle holder;
(xxxi) Syringes with needles 2 cc., 5 cc., 10 cc., and 50 cc.;
(xxxii) Suturing needles and materials;
(xxxiii) Rubber bandage — Pressure bandage;
(xxxiv) Twelve plain wooden splints, 350 mm. x 75 mm. X 6 mm.;
(xxxv) Twelve plain wooden splints 900 mm. x 100 mm. X 6 min.;
(xxxvi) Six plain wooden splints 250 mm. x 50 mm. x 12 mm.;
(xxxvii) An adequate supply of antitetanus toxiod;
(xxxviii) One bottle (120 ml.) of Spiritus Ammoniac Aromaticus (xxxix) Smelling salts (60 gm.);
(xl) Tablets: Anithistamine, Antispasmodic (25 each);
(xli) One bottle (one liter) carbolic lotion 1 in 20; (xlii) Coramine liquid (60 ml.);
(xliii) Injections; Morphia, pethedine, atropine, adrenaline, coramine, novocaine (6 each);
(xliv) Oxygen cylinder with necessary attachments;
(xlv) Four first-aid boxes or cupboards stocked to the scale, specified for Class C under Rule 63.
The ambulance room shall be in-charge of a qualified medical practitioner assisted by at least one qualified nurse and such staff as the Chief Inspector may deem necessary and direct in writing from time to time.
Explanation: For the purpose of this sub-rule, the expression "Qualified Medical Practitioner" means a person holding a qualification granted by an authority specified in the schedule to the Indian Medical Degrees Act. 1916 (Central Act VII of 1916), or in the schedule to the Indian Medical Council Act, 1956 (Central Act 102 of 1956).
A prominent notice containing the following particulars shall be displayed at a conspicuous place in the ambulance room
(a) the name, address and telephone number of the medical practitioner in charge; and
(b) the name of the nearest hospital and its telephone number.
The occupier of every factory to which sub-section (3) of section 45 of the Act and this rule (Rule 64) apply shall make all necessary arrangements for the expeditious removal in a suitable conveyance of serious cases of accident or sickness in the factory for further treatment to the nearest Government or other hospital, where the requisite facilities for the further treatment of such cases are available.
The Chief Inspector may, by an order in writing, exempt any factory from the requirements of this rule, subject to such conditions as he may specify in that order, if a properly equipped dispensary or hospital is available at or within one kilometer of the precincts of the factory and such arrangements are made by the occupier as to ensure the immediate treatment therein, of all injuries sustained by workers within the factory and for pro-viding rest to the injured workers.
65.Canteens
Rules 65 to 71 shall come into force in respect of any class or description of factories on such dates as the State Government may, by notification in the Official Gazette, appoint in this behalf.
The occupier of every factory notified by the State Government and wherein more than two hundred and fifty workers are ordinarily employed shall provide in or near the factory an adequate canteen according to the standards prescribed in these rules.
(2-A) In factories, in which workplaces are situated at a distance of more than 0.2 km. from the canteen and where the Chief Inspector directs in writing, arrangements shall be made for serving light refreshments from the canteen to workers at the workplaces. 147
The [Occupier or Manager of a factory] shall submit for the approval of the Chief Inspector plans and site plan, in triplicate, of the building to be constructed or adapted for use as a canteen.
The canteen building shall be situated not less than 15.2 meters from any latrine, urinal, boiler house, coal stacks, ash dumps and any other source of dust, smoke or obnoxious fumes:
Provided that the Chief Inspector may in any particular factory relax the provisions of this sub rule to such extent as may be reasonable in the circumstances and may require measures to be adopted to secure the essential purpose of this sub-rule.
The canteen building shall be constructed in accordance with the plans approved by the Chief Inspector and shall accommodate at least a dining hall, kitchen room, pantry and washing places separately for workers and for utensils. The minimum height of the building shall be not less than 3.7 meters and all the walls and roof shall be of suitable heat-resisting materials and shall be water-proof
In a canteen the floor and inside walls up to a height of 1.2 meters from the floor shall be made of smooth and impervious materials; the remaining portion of the inside walls shall be made smooth by cement plaster or in any other manner approved by the Chief Inspector.
The doors and windows of a canteen building shall be of fly-proof construction and shall allow adequate ventilation.
The canteen shall be sufficiently lighted at all times when any persons have access to it.
(a) In every canteen
(i) all inside walls of rooms and ceiling and passages and staircases shall be lime washed or colour washed at least once in each year or painted once in three years dating from the period when last lime washed or painted, as the case may be;
(ii) all wood work shall be varnished or painted once in three years dating from the period when last varnished or painted;
(iii) all internal structural iron or steel work shall be varnished or painted once in three years dating from the period when last varnished or painted:
Provided that inside walls of the kitchen shall be lime washed once in every four months;
(b) Records of dates on which lime washing, colour-washing, varnishing or painting is carried out shall be maintained in the prescribed register (Form No. 7).
The precincts of the canteen shall be maintained in a clean and sanitary condition. Waste water shall be carried away in suitable covered drains and shall not be allowed to accumulate so as to cause a nuisance. Suitable arrangement shall be made for the collection and disposal of garbage.
66.Dining hall
The dining hall shall accommodate at a time at least 30 percent of the workers working at a time: 148
Provided that, in any particular factory or in any particular class of factories, [the Chief Inspector of Factories may, by an order in writing] in this behalf, alter the percentage of workers to be accommodated.
The floor area of the dining hall, excluding the area occupied by the service counter and any furniture except tables and chairs, shall be not less than 0.9 square meters per diner to be accommodated as prescribed in sub-rule (1).
A portion of the dining hall and service counter shall be partitioned off and reserved for women workers in proportion to their number. Washing places for women shall be separate and screened to secure privacy.
Sufficient tables, chairs or benches shall be available for the number of diners or accommodated as prescribed in sub-rule (1):
Provided that where the Chief Inspector is satisfied that satisfactory alternate arrangements are made, he may exempt any particular factory or class of factories from the provisions of this sub-rule.
Soaps and towels should be provided at the washing places in the canteen for the use of the workers.
67.Equipment
There shall be provided and maintained sufficient utensils, crockery, cutlery, furniture and any other equipment necessary for the efficient running of the canteen. Suitable clean clothes for the employees serving in the canteen shall also be provided and maintained.
The furniture, utensils and other equipment shall be maintained in a clean and hygienic condition. A service counter, if provided, shall have a top of smooth and impervious material. Suitable facilities including an adequate supply of hot water shall be provided for the cleaning of utensils and equipment.
Food and food materials should be stored in fly-proof safe and handled with the help of wooden ladles or suitable metal forceps whichever is convenient. Vessels once used should be scalded before being used again.
67-A.Medical examination of Canteen Staff
Every member of the canteen staff who handles foodstuffs shall be medically examined by the Factory Medical Officer or the Certifying Surgeon and such examination shall include the following, namely:
(i) Routine and bacteriological testing of faces and urine for germs of dysentery and typhoid fever at intervals of not more than six months;
(ii) Routine blood examination at intervals of not more than twelve months;
(iii) Any other examination including chest X-rays that may be considered necessary by the Factory Medical Officer or the Certifying Surgeon. Any person, who in the opinion of the Factory Medical Officer as confirmed in writing by the Certifying Surgeon, is unsuitable for employment on account of possible risk to the health of others, shall not be employed as canteen staff.
(iv) 149
(a) [The fee for such routine clinical examination of each member of the 150 canteen staff by the certifying surgeons shall be [Rs.100/- (Rupees one hundred only)] which fee is exclusive of any charges incurred for conducting any kind of laboratory tests, etc.
(b) Such charges shall be paid by the occupier into the local treasury and the receipt attached with the application.] 151
(c) [The certificate of Medical Examination of Canteen Staff shall be issued in Form No. 40.]
68.Prices to be charged
Food, drinks and other items served in the canteen shall be served on a non-profit basis and the prices charged shall be subject to the approval of the Canteen Managing Committee. In the event of the Committee not approving the price list or where the Committee are equally divided on the issue, the price list should be sent to the Chief Inspector for approval. 152 (1-A) [In computing the prices referred to in sub-rule (I), the following items of expenditure shall not be taken into consideration, but will be borne by the occupier:
(a) the rent for the land and building;
(b) the depreciation and maintenance charges of the building and equipment provided for the canteen;
(c) the cost of purchase, repairs and replacement of equipment including furniture, crockery, cutlery and utensils;
(d) the water charges and expenses for providing lighting and ventilation
(e) the interest on the amount spent on the provision and maintenance of the building, furniture and equipment provided for the canteen;
(f) the cost of the fuel required for cooking or heating food-stuffs or water and
(g) the wages of the employees serving in the canteen and the cost of uniforms: if any, provided to them.]
The charge per portion of foodstuff beverages and any other item served in the canteen shall be conspicuously displayed in the canteen.
69.Accounts
All books of accounts, registers and any other documents used in connection with the running of the canteen shall be produced on demand to an Inspector of Factories.
The accounts pertaining to the canteen shall be audited once in every twelve months, by registered accountants and auditors. The balance-sheet prepared by the said auditors shall be submitted to the Canteen Managing Committee not later than two months after the closing of the audited accounts:
Provided that the accounts pertaining to the canteen in a Government Factory having its own Accounts Department may be audited in such Department.
70.Managing Committees
The manager shall appoint a Canteen Managing Committee which shall be consulted from time to time as to
(a) the quality and quantity of foodstuffs to be served in the canteen;
(b) the arrangements of the menus;
(c) times of meals to the canteen; and
(d) any other matter as may be directed by the Committee.
The Canteen Managing Committee shall consist of an equal number of persons nominated by the occupier and elected by the workers. The number of elected workers shall be in the pro-portion of one for every 1,000 workers employed in the factory, provided that in no case shall there be more than five or less than two workers on the Committee and in cases where the workers refuse to elect their representatives, the occupier shall himself nominate the worker's representatives.
The occupier shall appoint from among the persons nominated by him, a Chairman of the Canteen Managing Committee.
The manager shall determine and supervise the procedure for elections to the Canteen Managing Committee.
A Canteen Managing Committee shall be dissolved by the manager two years after the last election, no account being taken of a by-election or its constitution, as the case may be.
Where the workers of a factory in which a canteen has been provided by the occupier in accordance with rules 65 to 67 for the use of the workers, desire to run the canteen by themselves on a co-operative basis with share capital contributed by themselves, the management may permit them to run the canteen in accordance with the by-laws of the Co-operative Canteen, the Madras Co-operative Societies 153 Act, 1932, and the rules framed thereunder, subject to such conditions as the Chief Inspector may, in consultation with the Registrar of Co-operative Societies, Madras, impose.
The provisions of sub-rule (1) of rule 68, sub-rule (2) of rule 69 and sub-rules (1) to
(5) of rule 70 shall not apply to canteens which are run on co-operative basis by the workers themselves and which are recognized by the Chief Inspector.
71.Rule 71
The provisions of rules 65 to 70 may be relaxed by the Chief Inspector, subject to such conditions as he may deem fit, in the case of factories belonging to the same business groups or amalgamation where centralized cooking in an approved industrial canteen is arranged for. Adequate arrangements to the satisfaction of the Chief Inspector shall, however, be made in such cases for the conveyance and proper distribution of the food so cooked to the workers concerned as if separate canteens had actually been provided at site in the factories covered by this relaxation.
72.Shelters, rest rooms and lunch rooms
This rule shall apply to any factory wherein more than one hundred and fifty workers are ordinarily employed.
The shelters, or rest rooms and lunch rooms shall conform to the following 154 standards and the [Occupier or Manager of a factory] shall submit for the approval of the Chief Inspector plans and site plans in triplicate of the building to be constructed or adapted:
(a) The building shall be soundly constructed and all the walls and roof shall be of suitable heat-resisting materials and shall be water-proof. The floor and walls to a height of 91.4 centimeters shall be so laid or finished as to provide a smooth, hard and impervious surface.
(b) The height of every room in the building shall be not less than 3.7 meters from floor level to the lowest part of the roof and there shall be at least 1.1 square meters of floor area for every person employed:
Provided that (i) workers who habitually go home for their meals during the rest periods may be excluded in calculating the number of workers to be accommodated and (ii) in the case of factories in existence at the date of commencement of the Act, where it is impracticable, owing to lack of space to provide 1.1 square meters of floor area for each person, such reduced floor area per person shall be provided as may be approved in writing by the Chief Inspector.
(c) Effective and suitable provision shall be made in every room for securing and maintaining adequate ventilation by the circulation of fresh air and there shall also be provided and maintained sufficient and suitable natural or artificial lighting.
(d) Every room shall be adequately furnished with chairs or benches with back- rests.
(e) Sweepers shall be employed whose primary duty it is to keep the rooms, building and precincts thereof in a clean and tidy condition. 155
(ee) [Suitable provisions shall be made in every room for supply of drinking water and facilities for washing]
(f) The Chief Inspector may, for reasons to be recorded in writing, relax the provisions of this rule subject to such conditions as he may deem it to impose, in respect of factories in existence on the 1st April, 1949.
156
[A portion of the shelters or rest rooms and lunch rooms shall be partitioned off and reserved for women workers in proportion to their strength]
73.Cr è ches
157
Rules 73 to 76 shall apply to any factory wherein more than [Thirty women workers] are ordinarily employed. 158
The cr è ches shall conform to the following standards and the [Occupier or Manager of the factory] shall submit for approval of the Chief Inspector, detailed plans in triplicate of the building to be constructed or adapted.
The cr è che shall be conveniently accessible to the mothers of the children accommodated therein and so far as is reasonably practicable it shall not be situated in the close proximity to any part of the factory where obnoxious fumes, dust or odours are given off or in which excessively noisy processes are carried on.
The building in which the cr è che is situated shall be soundly constructed and all the walls and roof shall be of suitable heat-resisting materials and shall be water-proof. The floor and internal walls of the cr è che to a height of 1.2 meters all round shall be so laid or finished as to provide a smooth impervious surface.
The height of the rooms in the building shall be not less than 3.7 meters from the floor to the lowest part of the roof and then shall be not less than 1.9 square meters or floor area for each child to be accommodated.
Effective and suitable provision shall be made in every part of the cr è che for securing and maintaining adequate ventilation by the circulation of fresh air.
The cr è che shall be adequately furnished and equipped and in particular there shall be one suitable cot or cradle with the necessary bedding for each child (provided that for children over two years of age it will be sufficient if suitable bedding is made available) at least one chair or equivalent seating accommodation for the use of each mother while she is feeding or attending to her child and a sufficient supply of suitable toys for the older children.
A suitably fenced and shady open air playground shall be provided for the older children:
Provided that the Chief Inspector may by order in writing exempt any factory from compliance with this sub-rule if he is satisfied that there is not sufficient space available for the provision of such a playground.
74.Wash room
There shall be in or adjoining the cr è che a suitable wash room for the washing of the children and their clothing. The wash room shall conform to the following standards:
(a) The floor and internal walls of the room to a height of 91.4 centimeters shall be so laid or finished as to provide a smooth impervious surface. The room shall be adequately lighted and ventilated and the floor shall be effectively drained and maintained in a clean and tidy condition.
(b) There shall be at least one basin or similar vessel for every four children accommodated in the cr è che at any one time together with a supply of water provided, if practicable, through taps from a source approved by the Health Officer. Such source shall be capable of yielding for each child a supply of at least 22.7 liters of water a day.
(c) An adequate supply of clean clothes, soap and clean towels shall be made available for each child while it is in the cr è che.
(d) Adjoining the washing room referred to above, a septic type latrine shall be provided for the sole use of the children in the cr è che. The design of this latrine and the scale of accommodation to be provided shall be determined by the Health Officer. The cr è che latrine shall always be kept clean and in a sanitary condition by a sweeper specially employed for the purpose.
75.Supply of milk and refreshment
At least 284.1 milliliters of clean pure milk shall be available for each child on every day it is accommodated in the cr è che and the mother of such a child shall be allowed in the course of her daily work, intervals of at least 15 minutes to feed the child. For children above two years of age there shall be provided in addition an adequate supply of wholesome refreshment.
76.Cr è che staff and clothes for cr è che staff
The occupier shall appoint a qualified nurse or midwife with sufficient number of ayahs, the number calculated at the rate of one ayah for every 30 children or part thereof for the purposes of looking after the children accommodated in the cr è ches and the occupier shall provide suitable equipment and the facilities for the purpose:
Provided that the occupier may appoint a nurse or midwife who is not qualified if the Chief Inspector, in consultation with the Director of Medical Services, certifies that such nurse or midwife is suitable for appointment under this sub-rule.
The cr è che staff shall be provided with suitable clean clothes by the occupier for use while on duty in the cr è che.
159
76-A.Exemption from the provisions of cr è che
In factories where the number of married women or widows employed does not exceed 15 or where the factory works for less than 180 days in a calendar year, or where number of children kept in the cr è che was less than 5 in the preceding year, the Chief Inspector may exempt such factories from the provisions of section 48 and rules 73 to 76 if he is satisfied that alternate arrangements as stipulated under sub- rule (2) are provided by the factory.
(a) The alternate arrangements required in sub-rule (1) shall include a cr è che 160 building, which has a minimum accommodation at the rate of [1.9 meter] per child and constructed in accordance with the plans approved by the aid Inspector.
(b) The cr è che building shall have
(i) a suitable wash room for washing of the children and their clothing;
(ii) adequate supply of soap, clean clothes and towels; and
(iii) adequate number of female attendants who are provided with suitable clean clothes for use, while on duty, to look after the children in the cr è che.
161 [(2-A)
(a) If factories or group of factories or cluster of factories in an area which are statutorily required to provide a cr è che, decide by mutual agreement among themselves to provide a common cr è che in the form of a group or chain of cr è ches, within one kilometer radius from such factories and to share the expenditure and maintenance in the running of such common cr è che facilities, proportionate to the number of eligible children, such factories may apply to the Chief Inspector in writing for grant of exemption from providing a separate cr è che. The Chief Inspector may exempt such factories from providing a separate cr è che, subject to such conditions as he may deem fit, after satisfying himself that the alternate arrangements are adequate and appropriate to meet the needs of all the eligible employees in such factories;
(b) Where the factories in an area, on payment of contribution proportionate to the number of the eligible children, avail the common cr è che facilities provided by the promotional institutions such as Small Industries Development Corporation, State Industries Promotional Corporation of Tamil Nadu Limited or by the Employers' Association or by voluntary organisations aided by the State Government or Central Government, such factories may apply to the Chief Inspector in writing for grant of exemption from providing a separate cr è che. The Chief Inspector may exempt such factories from providing a separate cr è che, subject to such conditions as he may deem fit, after satisfying himself that the alternate arrangements are adequate and appropriate to meet the needs of all the eligible employees in such factories.]
The exemption granted under sub-rule (1) may at any time be withdrawn by the Chief Inspector if he finds after such enquiry as he may deem fit, that the factory has committed a breach of this rule,]
