The Tamil Nadu Factories Rules, 1950
Arrangement of Rules
G.O. No. 1041 of 1950 · Tamil Nadu · 68 chapters and schedules, 167 rules
Chapter IV
SAFETY
53.Further safety precautions
Without prejudice to the provisions of sub-section (1) of section 21 in regard to the fencing of machines, the further precautions specified in the schedules annexed hereto shall apply to the machines noted in each schedule.
This rule shall come into force, in respect of any class or description of factories. where machines noted In the said schedules are in use, on such dates as the State Government may, by notification in the Official Gazette, appoint in this behalf.
[Register prescribed under section 22(1): Register to record the names of specially trained adult workers shall be in Form No. 35 and this register shall be made available for inspection at all times and produced on demand during working hours or when any work is being carried on in the factory.]
54.Employment of young person ’ s on dangerous machines
[The machines specified in Sections 28, 29 and 30 and the machines mentioned below] shall be deemed to be of such dangerous character that young person ’ s shall not work at them unless the provisions of section 23 (1) are complied with:
Power presses other than hydraulic presses; milling machines used in the metal trades;
Guillotine machines;
Circular saws;
Platen printing machines;
Decorticator;
Oil expeller;
54A.Rule 54A
The following pans of machines will be deemed to be machinery to be guarded by the makers for the purpose of section 26 (1):
The platen motion of letter printing machine.
Reciprocating dies of power presses.
Reciprocating knife of the guillotine machine.
Revolving drums and cylinders in all machines, such as groundnut seed crustier, soap mixtures and foundry tumblers.
Revolving beaters in groundnut decorticator.
Abrasive wheels.
Projections on revolving parts such as key heads set screws, cotton pins and coupling bolts.
Revolving open arm pulleys including fan blades.
Back gears, change wheels and cog driver of lathes.
Level drives of planning, shaping, slotting, drilling and milling machines.
All cog and level drives of oil expellers,
55.Hoists and lifts
[A Register shall be maintained to record particulars of examination of hoists and lifts and shall give particulars as shown in Form No. 36.]
Exemption of certain hoists and lifts: In pursuance of the provisions of sub-section
(4) of section 28. in respect of any class or description of hoist or lift specified in the first column of the following schedule, the requirements of section 28 specified in the second column of the said schedule and set opposite to that class or description of hoist or lift shall not apply.
55A.Lifting machines, chains, ropes and lifting tackles
No lifting machine and no chain, rope or lifting tackle, except a fiber rope or fiber rope sling, shall be taken into use in any factory for the first time in that factory unless it has been tested and all parts have been thoroughly examined by a competent person and a certificate of such a test and examination specifying the safe working load or loads and signed by the person making the test and the examination, has been obtained and is kept available for inspection.
Every jib crane so constructed that the safe working load may be varied by the raising or lowering of the jib. shall have attached thereto either an automatic indicator of safe working loads or an automatic jib angle indicator and a table indicating the safe working loads at corresponding inclinations of the jib or corresponding radii of the load.
A table showing the safe working loads of every kind and size of chain, rope or lifting tackle in use, and in the case of a multiple sling, the safe working load at different angles of the legs, shall be posted in the store in which the chains, ropes or lifting tackles are kept, and in prominent positions on the premises, and no chain, rope or lifting tackle not shown in the table shall be used. This sub-rule shall not apply in respect of any lifting tackle if the safe working loads thereof or in the case of a multiple sling, the safe working load at different angles of the legs is plainly marked upon it.
The register to be maintained under clause (a) (iii) of sub-section (1) of section 29 of the Act shall contain the following particulars and shall be kept readily available for inspection:
(i) Name of occupier of factory.
(ii) Address of the factory.
(iii) Distinguishing number or mark, if any and description sufficient to identify the lifting machine, chain, rope or the lifting tackle.
(iv) Date when the lifting machine, chain, rope or lifting tackle was first taken into use in the factory.
(v) Date and number of the certificate relating to any test and examination made under sub-rules (I) and (8) together with the name and address of the person who issued the certificate.
(vi) Date of each periodical thorough examination made under clause (a) (iii) of sub-section (I) of section 29 of the Act and sub-rule (7) and by whom it was carried out.
(vii) Date of annealing or other heat treatment of the chain and other lifting tackle made under sub-rule (6) and by whom it was carried out.
(viii) Particulars of any defects found at any such thorough examination or after annealing and affecting the safe working load, and of the steps taken to remedy such defects.
Passage ways for cranes
(i) To provide access to mil tracks of overhead travelling cranes suitable passage- ways of at least 50cm. (20 inches) width with toe boards and double hand rails 90 cm. (3 feet) high shall be provided alongside, and clear of the rail tracks of overhead travelling cranes, such that no moving part of the crane can strike persons on the ways, and the passage-way shall be at a lower level than the crane can strike persons on the ways, and the passage-way shall be at a lower level than the crane track itself. Safe access ladders shall be provided at suitable intervals to afford access to these passage-ways, and from passage- ways to the rail tracks.
(ii) [The Chief Inspector may, for reasons to be specified in writing, exempt any factory in respect of any overhead travelling crane from the operation of any provisions of clause (i) subject to such conditions as he may specify.]
All rails on which a travelling crane moves and every track on which the carriage of a transporter or runway moves shall be of proper size and adequate strength and have an even running surface and every such rail or track shall be properly laid, adequately supported and properly maintained.
All chains, and lifting tackle, except a rope sling shall, unless they have been subjected to such other heat treatment as may be approved by the Chief Inspector, be effectively annealed under the supervision of a competent person at the following intervals:
(i) All chains, slings, rings, hooks, shackles and swivels used in connection with molten metal or molten slag or when they are made of 12.7 millimeters bar or smaller, once at least in every six months.
(ii) All other chains, rings, hooks, shackles and swivels in general use, once at least in every twelve month:
Provided that chains and lifting tackle not in frequent use shall, subject to the Chief Inspector's approval, be annealed only when necessary. Particulars of such annealing shall be entered in a register prescribed under sub-rule (4) which shall be kept available for inspection.
Nothing in the foregoing sub-rule (6) shall apply to the following classes of chains and lifting tackle:
(i) Chains made of malleable cast iron.
(ii) Plate link chains.
(iii) Chains, rings, hooks, shackles and swivels made of steel or of any non-ferrous metals.
(iv) Pitched chains, working on sprocket or pocketed wheels.
(v) Rings, hooks, shackles and swivels permanently attached to pitched chains, pulley blocks or weighing machines.
(vi) Hooks and swivels having screw threaded parts or ball-bearing or other case- hardened parts.
(vii) Socket shackles secured to wire ropes by white metal capping.
(viii) Bordeaux connections.
Such chains and lifting tackles shall be thoroughly examined by a competent person once at least in every twelve months and particulars entered in the register kept in accordance with sub-rule (4).
All lifting machines, chains, ropes and lifting tackle, except a fiber rope or fiber rope sling, which have been lengthened, altered or repaired by welding or otherwise shall, before being again taken into use, be adequately i.e., tested and re-examined by a competent person and a certificate of such test and examination be obtained and particulars entered in the register kept in accordance with sub-rule (4).
No person under 18 years of age and no person who is not sufficiently competent and reliable shall be employed as driver of a lifting machine whether driven by mechanical power or otherwise, or to give signals to a driver
56.Pressure Plant
Definition In this rule
(a) ‘ design pressure ' means the maximum pressure that a pressure vessel or plant is designed to withstand safely when operating normally
(b) 'maximum permissible working pressure' is the maximum pressure at which a pressure vessel or plant is permitted to be operated or used under this rule and is determined by the technical requirements of the process
(c) ‘ plant' means a system of piping that is connected to a pressure vessel and is used to contain a gas vapour or liquid under pressure greater than the atmospheric pressure, and includes the pressure vessel
(d) 'pressure vessel ' means [a] vessel that may be used for containing, storing, distributing, transferring, distilling, processing or other-wise handling any gas, vapour or liquid under pressure greater than the atmospheric pressure and includes any pipeline fitting or other equipment attached thereto or used in connection therewith; and
(e) ["notified person " means a person notified by the State Government, for the purpose of this rule;
Exceptions Nothing in this rule shall apply to
(a) [* * *]
(b) vessels made of ferrous materials having an internal operating pressure not exceeding 1 kg/cm (I5 1 bs/square inch);
(c) steam boiler, steam and feed pipes and their fittings coming under the purview of Indian Boilers Act, 1923 (Central Act V of 1923);
(d) metal bottles or cylinders used for storage or transport of compressed gases or liquefied or dissolved gases, under pressure covered by the Gas Cylinder Rules, 1940 framed under the Indian Explosives Act. 1884 (Central Act IV of 1884):
(e) vessels in which internal pressure is due solely to the static head of liquid
(f) vessels with a nominal water capacity not exceeding 500 liters connected in a water-pumping system containing air that is compressed to serve as a cushion;
(g) vessel for nuclear energy application;
(h) refrigeration plant having a capacity of three tons or less of refrigeration in 24 hours; and
(i) working cylinders of steam engines or prime movers, feed pumps and steam traps; turbine castings; compressor cylinders steam separators or drivers: steam strainers; steam desuper heaters; oil separators:air receivers for fire sprinklers installations; air receivers of monotype machines provided the maximum working pressure of the air receiver does not exceed 1.33kg.f/cm.(201bs/sq inch) and the capacity 84.95 liters (3 cu.ft); air receivers of electrical circuit breakers; air receivers of electrical relays; air vessels on pumps, pipe coils, accessories of instruments and appliances, such as cylinders and piston assemblies used for operating relays and inter-locking type of guards; vessels with liquids subjected to static head only; and hydraulically operating cylinders other than any cylinder communicated with an air loaded accumulator.
Design and construction Every pressure vessel or plant used in a factory
(a) shall be properly designed on sound engineering practice;
(b) shall be of good construction. sound material, adequate strength and free from any patent defects; and
(c) shall be properly maintained in a safe condition:
Provided that a pressure vessel or plant in respect of the design and construction of which there is an Indian Standard or a standard of the country of manufacture or any other law or regulation in force, shall be designed and constructed in accordance with the said standard, law or regulation, as the case may be and certificate thereof shall be obtained from the manufacturer or from the [notified person] which shall be kept and produced on demand by an Inspector.
Safety devices Every pressure vessel shall be fitted with
(a) a suitable safety valve or other effective pressure relieving device of adequate capacity to ensure that the maximum permissible working pressure of the pressure vessel shall not be exceeded. It shall be set to operate at a pressure not exceeding the maximum permissible working pres-sure and when more than one protective device is provided, only one of the devices need be set to operate at the maximum permissible working pressure and the additional device shall be set to discharge at a pressure not more than 5 percent. in excess of the maximum permissible working pressure;
(b) a suitable pressure gauge with a dial range not less than 1.5 times the maximum permissible working pressure. easily visible and designed to show at all times the correct internal pressure and marked with a prominent red mark at the maximum permissible working pressure of the pressure vessel:
(c) a suitable nipple and globe valve connected for the exclusive purpose of attaching a test pressure gauge for checking the accuracy of the pressure gauge referred to in clause (b) of this sub-rule:
(d) a suitable stop valve or valves by which the pressure vessel may be isolated from other pressure vessels or plant or source of supply of pressure. Such a stop valve or valves shall be located as close to the pressure vessel as possible and shall be easily accessible; and
(e) a suitable drain cock or valve at the lowest part of the pres-sure vessel for the discharge of the liquid or other substances that may collect in the pressure vessel:
Provided that it shall be sufficient for the purpose of this sub-rule if the safety valve or pressure relieving device, the pressure gauge and the stop valve are mounted on a pipeline immediately adjacent to the pressure vessel and where there is a range of two or more similar pressure vessels served by the same pressure lead, only one set of such mountings need be fitted on the pressure lead immediately adjacent to the range of pressure vessels, provided they cannot be isolated.
Pressure reducing devices
(a) Every pressure vessel which is designed for a working pressure less than the pressure at the source of supply, or less than the pressure which can be obtained in the pipe connecting the pressure vessel with any other source of supply, shall be fitted with a suitable pressure reducing valve or other suitable automatic device to prevent the maximum permissible working pressure of the pressure vessel being exceeded;
(b) To further protect the pressure vessel in the event of failure of the reducing valve or device, at least one safety valve having a capacity sufficient to release all the steam, vapour or gas without undue pressure rise as determined by the pressure at the source of supply and the size of the pipe connecting the source of supply, shall be fitted on the low pressure side of the reducing valve.
Pressure vessel or plant being taken into use
(a) No new pressure vessel or plant shall be taken into use in a factory after coming into force of this rule unless it has been hydrostatically tested by a competent person at a pressure at least 1.3 times the design pressure, and no pressure vessel or plant which has been previously used or has remained isolated or idle for a period exceeding two months or which has undergone alterations or repairs shall be taken into use in a factory unless it has been thoroughly examined by a [notified person] externally, and internally if practicable, and has been hydrostatically tested by the [notified person] at a pressure which shall be 1.5 times the maximum permissible working pressure:
Provided, however, that the pressure vessel or plant which is so designed and constructed that it cannot be safely filled with water or liquid or is used in service even some traces of water cannot be tolerated, shall be pneumatically tested at a pressure not less than the design pressure or the maximum permissible working pressure as the case may be:
Provided further that the pressure vessel or plant which is lined with glass shall be tested hydrostatically or pneumatically as required at a pressure not less than the design pressure or maximum permissible working pressure as the case may be.
Design pressure shall be not less than the maximum permissible working pressure and shall take into account the possible fluctuations of pres-sure during actual operation.
(b) No pressure vessel or plant shall be used in factory unless there has obtained from the maker of the pressure vessel or plant or from the [notified person] a certificate specifying the design pressure or maximum-permissible working pressure thereof, and stating the nature of tests to which the pressure vessel or plant and its fittings (if any) have been subjected, and every pressure vessel or plant so used in a factory shall be marked so as to enable it to be identified as to be the pressure vessel or plant to which the certificate relates and the certificate shall be kept available for perusal by the Inspector.
(c) No pressure vessel or plant shall be permitted to be operated or used at a pressure higher than its design pressure or maximum permissible working pressure as shown in the certificate.
In service test and examinations 100 Every pressure vessel or plant in service shall be thoroughly examined by a [notified person]
(a) Externally, once in every six months;
(b) internally, once in every twelve months.
If by reason of the construction of a pressure vessel or plant, a thorough internal examination is not possible this examination may be replaced by a hydrostatic test which shall be carried out once in every two years:
Provided that for a pressure vessel or plant in continuous process which cannot be frequently opened, the period of internal examination may be extended to four years;
(c) hydrostatically tested once in every four years; and
(d) the hydrostatic test pressure to be carried out for the purpose of this rule shall be 1.25 times the design pressure or 1.5 times the maximum permissible working pressure whichever is less:
Provided that in respect of a pressure vessel or plant with thin walls such as sizing cylinder made of copper or any other non-ferrous metal, periodic hydrostatic test may be dispensed with subject to the condition that the requirements laid down in sub-rule (8) are fulfilled:
Provided further that when it is impracticable to carry out thorough external examination of any pressure vessel or plant every six months as required in clause
(a) of this sub-rule, or if owing to its construction and use a pressure vessel or plant cannot be hydrostatically tested as required in clauses (d) and (c) of this sub-rule, a thorough external examination of the pressure vessel or plant shall be carried out at least once in every period of two years; and at least once in every period of four years thorough systematic non-destructive test like ultrasonic test for thickness or other defects of all parts the failure of which might lead to eventual rupture of the pressure vessel or plant shall be carried out.
Thin walled pressure vessel or plant
(a) In respect of any pressure vessel or plant of thin walls such as sizing cylinder made of copper or any other non-ferrous metal the maximum permissible working pressure shall be reduced at the rate of 5 per cent. of the original maximum permissible working pressure for every year of its use after the first five years and no such cylinder shall he allowed to continue to be used for more than twenty years after it was first taken into use
(b) If any information as to the date of construction. thickness of walls, or maximum permissible working pressure is not available, the age of such 101 pressure vessel or plant shall be determined by the [notified person] in consultation with the Chief Inspector from the other particulars available with the manager;
(c) Every new and second hand pressure vessel or plant of thin walls to which repairs likely to affect its strength or safety have been carried out shall be tested before use to at least 1.5 times its maximum permissible working pressure.
102
[Report by notified person]
(a) If during any examination any doubt arises as to the ability of the pressure vessel or plant to work safely until the next prescribed examination, the [notified person] shall enter in the prescribed register his observations, findings and conclusions with other relevant remarks with reasons and may authorize the pressure vessel or plant to be used and kept in operation subject to a lowering of maximum permissible working pressure. or to more frequent or special examination or test, or subject to both of these conditions;
(b) A report of the result of every examination or test carried out shall be completed in the prescribed Form No. 8 and shall be signed by the person making the examination or test, and shall be kept available for perusal by the Inspector at all hours when the factory or any part thereof is working:
(c) Where the report of any examination under this rule specified any condition for securing the safe working of any pressure vessel or plant. the pressure vessel or plant shall not be used unless the specified condition is fulfilled 103
(d) The [notified person] making report of any examination under this rule, shall within seven days of the completion of the examination send to the Inspector a copy of the report in every case where the maximum permissible working pressure is reduced or the examination shows that the pressure vessel or plant or any part thereof cannot continue to be used with safety unless certain repairs are carried out or unless any other safety mea-sure is taken.
Application of other laws
(a) The requirements of this rule shall be in addition to and without any prejudice to and not in derogation of the requirements of any other law in force:
(b) Certificates or reports of any examination. or test of any pressure vessel or plant to which sub-rules (7) to (9) do not apply, conducted or required to be conducted under any other law in force and other relevant record relating to such pressure vessel or plant, shall be properly maintained as required under the said law and shall be produced on demand by the Inspector.
56-A.Water sealed gas holder
The expression "gas holder" means a water sealed gas holder which has a storage capacity of not less than 141.5 cubic meters (5000 cu. ft).
Every gas holder shall be of good construction, sound material adequate strength and properly maintained.
Where there is more than one gas holder in the factory every gas holder shall be matted in a conspicuous position with a distinguishing number or letter. 104
Every gas holder shall be thoroughly examined externally by a [Notified person] at least once in every period of 12 months.
In the ease of a gas holder of which any lift has been in use for more than 10 years, the internal state of the sheeting shall, within one year of the coming into force of this rule and thereafter at least once in every period of four years, be examined by a 105 [notified person] by means of electronic or other accurate devices;
Provided that if the Chief Inspector is satisfied that such electronic or other accurate devices are not available, he may permit the cutting of samples from the crown and the sides of holder:
Provided further, that if such inspection raises a doubt, an internal visual examination shall be made.
All possible steps shall be taken to prevent or minimize ingress of impurities in the gas holder.
No gas holder shall be repaired or demolished except under the direct supervision of a person who, by reason of his training and experience and of his knowledge of the necessary precautions against risks of explosion and of persons being overcome by gas, is competent to supervise such work.
(i) All sample discs cut under sub-rule (5) shall be kept readily available for inspection.
(ii) A permanent register duly signed by the occupier or man-ager shall be maintained giving the following particulars, namely:
(a) the distinguishing number or letter of the gas holder-specified under sub-rule (3) and the particulars of manufacture relating to the maker's name, date of manufacture, capacity number of lifts and pres-sure thrown by holder when lull of gas
(b) the dates of examination carried out as required by sub-rules (4) and (5) and by whom carried out
(c) the method of examination used;
(d) date of painting and other similar particulars:
(e) nature of repairs and name of persons carrying out such repairs: and
(f) other remarks if any. 106
(iii) The results of examinations by a [notified person] carried out under sub- rules (4) and (5) shall be in Form No. 8-A.
(iv) A copy of the report in Form No. 8-A shall be kept in the register and both the register and the report shall be readily available for inspection by an Inspector.
The Inspector shall ensure that every gas holder is duly examined periodically as required by sub-rules (4) and (5).
107
56-B.Testing or Examination of Pressure Plant or Vessel
An application duly filled in Form No. 8-B for the-testing or examination of pressure plant or vessel or water sealed gas holder shall be submitted to the respective 108 Deputy Chief Inspector of Factories [***] 109
[The fee payable for the examination and testing of pressure plant or vessel or water sealed gas holder shall be as follows:
(i) Rs. 400 (Rupees four hundred only) per plant irrespective of its size or capacity for external examination;
(ii) Rs. 1000 (Rupees one thousand only) per plant unto 4 Kgf/Sq.cm(g) for Hydrostatic test:
(iii) R s. 2, 0 00 (R u p ee s t w o t h o u sa n d o nl y) p er p l a n t a bo ve 4 K g f / S q. c m. (g) f o r Hydrostatic test
(iv) Rs. 1,000 (Rupees one thousand only) per plant irrespective of the size or capacity for internal examination: and
(v) Rs. 4,000 (Rupees four thousand only) per plant or vessel irrespective of the size of capacity for non-destructive ultrasonic thickness gauging test. 110
Every application under sub-rule (1) shall be accompanied [by a treasury receipt or by a crossed demand draft drawn in any branch of a Nationalized Bank in favour of the respective Deputy Chief Inspector of Factories] evidencing payment of appropriate fee specified in sub-rule (2): and
The occupier shall apply for examination and testing of Pressure Vessel or Plant along with the prescribed application and fee one month in advance from the date on which the vessel or plain fall due for such examination or test.]
57.Excessive weights
(1) No man, woman or young person shall, unaided by another person, lift, carry or move by hand or head, any material, article, tool or appliance exceeding the maximum limit in weight set out in the following schedule: 111
58.Protection of eyes
Effective screens or suitable goggles shall be provided for the protection of persons employed in or in the immediate vicinity of the following processes.
(a) The processes specified in Schedule I annexed hereto, being processes which involve risk of injury to the eyes from particles or fragments thrown off in the course of the process.
(b) The processes specified in Schedule 11 annexed hereto, being processes which 113 involve risk of injury to the eyes by reason of exposure to excessive light [or infra- red or ultra-violet radiations.)
59.Minimum dimensions of manholes
Every chamber, tank, vat, pits- pipe, flue or other confined space, which persons may have to enter and which may contain dangerous fumes to such an extent as to involve risk of the persons being overcome thereby, shall unless there is other effective means of egress, be provided with a manhole which may be rectangular, oval or circular in shape, and which shall
(a) in the case of a rectangular or oval shape, be not less than 40.6 centimeters long and 30.5 centimeters wide;
(b) in the case of a circular shape, be not less than 40.6 centimeters in diameter.
60.Exemptions
The requirements of sub-section (4) of section 37 shall not apply to the following processes carried on in any factory:
(a) The operation of repairing a water sealed gas holder by the electric welding process Subject to the following conditions;
(i) The gas holder shall contain only the following gases separately or mixed at a pressure greater than atmospheric pressure, namely, town gas, coke-oven gas, producer gas, blast furnace gas or gases other than air, used in their manufacture:
Provided that this exemption shall not apply to any gas holder containing acetylene or mixture of gases to which acetylene bas been added intentionally.
(ii) Welding shall only be done by the electric welding process and shall be carried out by experienced operatives under the constant supervision of a competent person.
(b) The operations of cutting or welding steel or wrought iron gas mains and services by the application of heat, subject to the following conditions:
(i) The main or service shall be situated in the open air, and it shall contain only the following gases, separately or mixed at a pressure greater than atmospheric pressure, namely, gas, coke-oven gas, producer gas, blast furnace gas or gases other than air, used in their manufacture;
(ii) the main or service shall not contain acetylene or any gas or mixture of gases to which acetylene has been added intentionally;
(iii) the operation shall be carried out by an experienced person or persons and at least two persons (including those carrying out the operations) experienced in work on gas mains and over 18 years of age shall be present during the operation;
(iv) the site of the operation shall be free from any inflammable or explosive gas or vapour;
(v) where acetylene gas is used as a source of heat in connection with an operation, it shall be compressed and contained in a porous substance in a cylinder; and
(vi) prior to the application of any flame to the gas main or service, this shall be pierced or drilled and the escaping gas ignited.
(c) The operation of repairing an oil tank on any ship by the electric welding process, subject to the following conditions
(i) The only oil contained in the tank shall have a flash point of not less than o 150 F (dose test) and a certificate to this effect shall be obtained from a competent analyst;
(ii) the analyst's certificate shall be kept available for inspection by an Inspector or by any person employed or working on the ship;
(iii) the welding operation shall be carried out only on the exterior surface of the tank at a place (a) which is free from oil or oil leakage in inflammable quantities and (b) which is not less than 30.5 centimeter below the nearest part of the surface of the oil within the tank; and
(iv) welding shall be done only by the electric welding and shall be carried out by experienced operatives under the constant supervision of a competent person.
115
61.Fire protection
Processes, equipment, plant, etc., involving serious explosion and serious fire hazards.
(a) All processes, storages, equipments, plants, etc., invoking serious explosion and flash fire hazards shall be located in segregated building where the equipment shall be so arranged that only a minimum number of employees are exposed to such hazards at any one time.
(b) All industrial processes involving serious fire hazard should be located in buildings or work places separated from one another by walls of fire-resistant construction.
(c) Equipment and plant involving serious fire or flash fire hazard shall, wherever possible, be so constructed and installed that in case of fire, they can be easily isolated.
(d) Ventilation ducts, pneumatic conveyors and similar equipment involving a serious fire risk should be provided with flame-arresting or automatic fire extinguishing appliances or fire resisting dampers electrically interlocked with heat sensitive/smoke detectors and the air-conditioning plant system.
(e) In all workplaces having serious fire or flash fire hazards, passages between machines, installations or piles of material should be at least 90 cm. wide. For storage piles, the clearance between the ceiling and the top of the pile should not be less than 2 m.
Access for fire fighting
(a) Buildings and Plants shall be so laid out and roads, passage-ways, etc., so maintained as to permit unobstructed access for fire fighting.
(b) Doors and window openings shall be located in suitable positions on all external walls of the building to provide easy areas to the entire area within the building for lire fighting.
116
[Protection against lighting] Protection from lighting shall be provided for
(a) buildings in which explosive or highly flammable substances are manufactured, used, handled or stored;
(b) storage tanks containing oils, paints or other flammable liquids;
(c) grain elevators;
(d) buildings, tall chimneys or stacks where flammable gases, fumes, dust or lint are likely to be present; and
(e) Sub-station buildings and out-door transformers and switch yards.
Precautions against ignition Wherever there is danger of fire or explosion from accumulation of flammable or explosive substances in air:-
(a) all electrical apparatus shall either be excluded from the area of risk or they shall be of such construction and so installed and maintained as to prevent the danger of their being a source of ignition;
(b) effective measures shall be adopted for prevention of accumulation of static charges to a dangerous extent;
(c) workers shall wear shoes without iron or steel nails or any other exposed ferrous materials which is likely to cause sparks by friction;
(d) smoking, lighting or carrying of matches, lighters or smoking materials shall be prohibited;
(e) transmission belts with iron fasteners shall not be used; and
(f) all other precautions as are reasonably practicable, shall be taken by (sic) prevent initiation of ignition from all other possible sources such as open flames, frictional sparks overheated surfaces of machinery or plant, chemical or physical chemical reaction and radiant heat.
Spontaneous ignition - Where materials are likely to induce spontaneous ignition, care shall be taken to avoid formation of air pocket and to ensure adequate ventilation. The material susceptible to spontaneous ignition should be stored in dry condition and should be in heaps of such capacity and separated by such passage which will prevent fire. The materials susceptible to ignition and stored in the open shall be at a distance not less than 10 meters away from process or storage buildings.
Cylinders containing compressed gas - Cylinders containing compressed gas may only be stored in open if they are protected against excessive variation of temperature, direct rays of sun, or continuous dampness. Such cylinders shall never be stored near highly flammable substances, furnaces or hot process. The room where such cylinders arc stored shall have adequate ventilation.
Storage of flammable liquids
(a) The quantity of flammable liquids in any work room shall be the minimum required for the process or processes carried on in such room. Flammable liquids shall be stored in suitable containers with close fitting covers:
Provided that not more than 20 liters of flammable liquids having a flash point of 21 ° C or less shall be kept or stored in any work room.
(b) Flammable liquids shall be stored in closed containers and in limited quantities in well ventilated rooms of fire resisting construction which are isolated from the remainder of the building by fire walls and self closing fire doors.
(c) Large quantities of such liquids shall be stored in isolated adequately ventilated building of fire resisting construction or in storage tanks, preferably underground and at a distance from any building as required in the Petroleum Rules, 1976.
(d) Effective steps shall be taken to prevent leakage of such liquids into basements, sums or drains and to confine any escaping liquid within safe limit.
Accumulation of flammable dust, gas, fume or vapour in air or flammable material on the floors.
(a) Effective steps shall be taken for removal or prevention of the accumulation in the air of flammable dust, gas, fume or vapour to an extent which is likely to be dangerous.
(b) No waste material of a flammable nature shall be permitted to accumulate on the floors and shall be removed atleast one in a day or shift, and more often, when possible. Such materials shall be placed in suitable metal containers with covers wherever possible.
Fire exists
(a) in this sub-paragraph
(i) "Horizontal exit" means an arrangement which allows alternative egress from a floor area to another floor at or near the same level in an adjoining building or an adjoining part of the same building with adequate separation; and
(ii) “ travel distance" means the distance an occupant has to travel to reach an exit.
(b) An exit may be a doorway, corridor, passageway to an external stairway or to a verandah or to an internal stairway segregated from the rest of building by fire resisting walls which shall provide continuous and protected means of egress to the exterior of a building or to an exterior open space. An exit may also include a horizontal exit leading to an adjoining building at the same level.
(c) Lifts, escalators and revolving doors shall not be considered as exits for the purpose of this sub-paragraph.
(d) In every room of a factory exits sufficient to permit safe escape of the occupants in case of fire or other emergency shall be provided which shall be free of any obstruction.
(e) The exits shall be clearly visible and suitably illuminated with suitable arrangement, whatever artificial lighting is to be adopted for this purpose, to maintain the required illumination in case of dilute of the normal source of electric supply.
(f) The exits shall be marked in a language understood by the majority of the workers.
(g) Iron rung ladders or spiral staircases shall not be used as not be used as exit.
(h) Fire resisting doors or roller shutters shall be provided at appropriate places along the escape routes to prevent spread of fire and smoke, particularly at the entrance of lifts or stairs where funnel or flue effect may be created inducing an upward spread of fire.
(i) All exits shall provide continuous means of egress to the exterior of a building or to an exterior open space leading to a street.
(j) Exits shall be so located that the travel distance to reach atleast one of them on the floor shall not exceed 30 meters.
(k) In case of those factories where high hazard materials are stored or used, the travel distance to the exit shall not exceed 22.5 meters and there shall be atleast two ways of escape from every room, however small, except toilet rooms, so located that the points of access thereto are out of or suitably shielded from areas of high hazard.
(l) Wherever more than one exit is required for any room space or floor, exits shall be placed as remote from each other as possible and shall be arranged to provide direct access in separate directions from any point in the area served.
(m) The unit of exit width used to measure capacity of any exit shall be 50 cm. A clear width of 25 cm. shall be counted as an additional half unit Clear width of less than 25 cm. shall not be counted for exit width.
(n) Occupants per unit width shall be 50 for stairs and 75 for doors.
(o) For determining the exits required, the occupant load shall be reckoned on the basis of actual number of occupants within any floor area or 10 square meter per person, whichever is more.
(p) There shall not be less than two exits serving every floor area above and below the ground floor, and atleast one of them shall be an internal enclosed stairway.
(q) For every building or structure used for storage only, and every section thereof considered separately shall have access to atleast one exit so arranged and located as to provide a suitable means of escape for any person employed therein and in any such room wherein more than ten persons may be normally present, atleast two separate means of exit shall be available, as remote from each other as practicable.
(r) Every storage area shall have access to atleast one means of exit which can be readily opened.
(s) Every exit doorway shall open into an enclosed stairway, a horizontal exit on a corridor or passage way providing continuous and protected means of egress.
(t) No exit doorway shall be less than 100 cm in permitted (sic)
(u) Exit doorways shall open outwards, that is, away from the room but shall not obstruct the travel along any exit. No door when opened shall reduce the required width of stairway or landing to less than 90 cm overhead or sliding doors shall not be installed for this purpose.
(v) An exit door shall not open immediately upon a flight of stairs. A landing atleast 1.5 m. x 1.5 m. in size shall be provided in the stairway at each doorway. The level of landing shall be the same as that of the floor which it serves.
(w) The exit doorways shall be openable from the side which they serve without the use of a key.
(x) Exit corridors and passage ways shall be of a width not less than the aggregate required width of exit doorways leading from there in the direction of travel to the exterior.
(y) Where stairways discharge through corridors and passage ways, the height of the corridors and passage ways shall not be less than 2.4 meters.
(aa) A staircase shall not be arranged round a lift shaft unless the latter is totally enclosed by a material having a fire resistance rating not lower than that of the type of construction of the farmer.
(bb) Hallow combustible construction shall not be permitted.
(cc) The minimum width of an internal staircase shall be 100 cms
(dd) The minimum width of treads without nosing shall be 25 cm. for an internal staircase. The treads shall be constructed and maintained in a manner to prevent, slipping.
(ee) The maximum height of a risor shall be 19 cm. and the number of risors shall be limited to 12 per flight.
(ff) Hand rails shall be provided with a minimum height of 100 cm. and shall be firmly supported.
(gg) The use of spiral staircase shall be limited to low occupant load and to a building of height of 9 meters, unless they are connected to platform such as balconies and terraces to allow escapees to pause. A spiral staircase shall be not less than 300 cm. in diameter and have adequate head room.
(hh) The width of a horizontal exit shall be same as for the exit doorways.
(ii) The horizontal exit shall be equipped with atleast one fire door of self closing type.
(jj) The floor area on the opposite or refuge side of a horizontal exit shall be sufficient to accommodate occupants of the floor areas served, allowing not less than 0.3 square meter per person. The refuge area shall be provided with exits adequate to meet the requirements of this sub-rule at least one of the exits shall lead directly to the exterior or street.
(kk) Where there is difference in level between connected areas for horizontal exit, rams not more than 1 in 8 slope shall be provided. For this purpose steps shall not be used.
(ll) Doors in horizontal exits shall be openable at all times
(mm) Ramps with a slope of not more than 1 in 10 may be substituted for the requirements of staircase. For all slopes exceeding 1 in 10 and wherever the use is such as to involve danger of slipping, the ramp shall be surfaced with non-slipping materials.
(nn) in any building not provided with automatic fire alarm a manual fire alarm system shall be provided if the total capacity of the building is over 500 persons, or if more than 25 persons are employed above or below the ground floor, except that no manual fire alarm shall be required in one-storey buildings where the entire area is undivided and all parts thereof are clearly visible to all occupants.
First-aid fire-fighting arrangements
(a) In every factory there shall be provided and maintained adequate and suitable firefighting equipment for fighting fires in the early stages, those being referred to as first-aid firefighting equipment in this rule. 117
(b) [The types of first-aid firefighting equipment to be provided shall be determined by considering the different types of fire risks which are classified as follows:
(i) "Class 'A' fire" Fire due to combustible materials such as wood, textiles, paper, rubbish and the like.
(ii) "Class 'B' fire"- Fire involving flammable liquids or liquefiable solids or the like where a blanketing effect is essential
(iii) "Class 'C' fire"- Fire involving flammable gases under pressure including liquefied gases, where it is necessary to inhibit the burning gas at fast rate with an inert gas, powder or vaporizing liquid for extinguishment
(iv) "Class 'D' fire" Fire involving combustible metals, such as magnesium, aluminium, zinc, sodium, potassium, etc., when the burning metal are reactive to water and water containing agents and in certain cases carbon dioxide, halogenated hydrocarbons and ordinary dry powders. This type of fire requires special media and techniques to extinguish
(c) The number and types of first aid firefighting equipment to be provided shall be as per Bureau of Indian Standards recommendations for installation of fire extinguishers given in Annexure B of IS 2190:1992. The types are detailed in Schedule-I.]
(d) The first-aid firefighting equipment shall conform to the relevant Indian Standards.
(e) As far as possible the first-aid firefighting equipment shall all be similar in shape and appearance and shall have the same method operation.
(f) All first-aid firefighting equipment shall be placed in a conspicuous position and shall be readily and easily accessible for immediate use. Generally, these equipment shall be placed as near as possible to the exits or stair landing or normal routes of escape.
(g) All water buckets and bucket pump type extinguishers shall be filled with clean water. All sand buckets shall be filled with clean, dry and fine sand.
(h) All other extinguishers shall be charged appropriately in accordance with the instructions of the manufacturer.
(i) Each first-aid fire-fighting equipment shall be allotted to a serial number by which it shall be referred to in the records. The following details shall be painted with white paint on the body of each equipment:
(1) Serial number:
(2) Date of last refilling; and
(3) Date of last inspection.
(j) First-aid firefighting equipment shall be placed on plat-forms or in cabinets in such a way that their bottom is 750 trim, above the floor level. Fire buckets shall be placed on hooks attached to a suitable stand or valve in such a way that their bottom is 720 mm. above the floor level. Such equipment if placed outside the building, shall be under sheds
(k) All extinguishers shall be thoroughly cleaned and re-charged immediately after discharge. Sufficient refill material shall be kept readily available for this purpose at all times.
(l) All first-aid fire-fighting equipment shall be subjected to routine maintenance, inspection and testing to be carried out by properly trained persons. Periodicity of the routine maintenance, inspection and test shall conform to the relevant Indian Standards.
Other fire-fighting arrangements
(a) In every factory, adequate provision of water supply for firefighting shall be made and where the amount of water required in liters per minute, as calculated from the formula A plus B plus C Plus D divided by 20 in 550 or more power driven trailer pumps of adequate capacity to meet the requirement of water as calculated above shall be provided and maintained. THE TABLE Capacity of Static Storage Exclusively Reserved for Sl.No Nature of Risk Hydrant Services.
(1) (2) (3) Not less than 1 hour aggregate pumping capacity with 1 Light Hazard a minimum of 1,35,000 liters 2 Ordinary Hazard Not less than 2 hours aggregate pumping capacity 3 High Hazard A Not less than 3 hours aggregate pumping capacity 4 High Hazard B Not less than 4 hours aggregate pumping capacity 1. LIGHT HAZARD OCCUPANCIES 1 Abrasive Manufacturing Premises 2 Aerated Water Factories 3 Agarbatti Manufacturing 4 Aluminum, Zinc and Copper Factories. 5 Analytical and/or Quality Control Laboratories 6 Asbestos Steam Packing and Lagging Manufactories 7 Battery Charging/Service Station 8 Battery Manufactories 9 Breweries 10 Brick Works 11 Canning Factories 12 Cardamom Factories 13 Cement Factories and/or Asbestos Products Manufacturing. 14 Ceramic Factories and Crockery and Stoneware Pipe Manufacturing 15 Cinema Theatres (including Preview Theatres) 16 Clay works 17 Clock and Watch Manufacturing 18 Clubs 19 Coffee Curing an Roasting Premises 20 Computer installation (Main Frame). 21 Condensed Milk Factories, Milk Pasteurizing Plant and Dairies 22 Confectionery Manufacturing 23 Dwellings 24 Educational and Research Institutes 25 Electric Generating Houses (Hydel) 26 Electric Lamps (incandescent and Fluorescent) and TV Picture Tube Manufacturing 27 Electric Sub-Station Distribution Station. 28 Electroplating Works. 29 Electronic and/or Computer Equipments Assemble and Manufactures. 30 Empty containers Storage Yard. 31 Engineering Workshops 32 Fruits and Vegetables Dehydrating/Drying Factories 33 Fruit Products and Condiment Factories 34 Glass and Glass Fiber Manufacturing 35 Godowns and warehouses storing non-combustible Goods. 36 Green Houses. 37 Gold Thread Factories/Gliding Factories. 38 Gum and/or Glue and Geletine Manufacturing 39 Hospital including X-ray and other Diagnostic Clinics. 40 Ice Candy and Ice-cream Manufacturing 41 Ice Factories 42 Ink (excluding Printing Ink) Factories. 43 Laundries. 44 Libraries. 45 Mica Products Manufacturing 46 Office premises 47 Places of worship 48 Pottery Works 49 Poultry Farms 50 Residential Hotels, Cafes and Restaurants 51 Salt Crushing Factories and Refineries. 52 Stables 53 Steel Plants(other than Gas based) 54 Sugar candy Manufacturing 55 Sugar Factories and Refineries 56 Tea Blending and Tea Packing Factories 57 Umbrella Assembling Factories 58 Vermicelli Factories 59 Water Treatment/Water Filtration Plants and Water Pump House. 2. ORDINARY HAZARD OCCUPANCIES 1 Airport and other Transportation Terminal Building 2 Areca Nut Slicing and/or Beterl Nut Factories 3 Atta and Cereal Grinding 4 Bakeries 5 Beedi Factories 6 Biscuit Factories 7 Bobbin Factories 8 Book Binder, Envelopes and Paper Bag Manufactures 9 Bulk Storage 10 Cable Manufacturing 11 Camphor Boiling 12 Candle Works 13 Carbon Paper/Typewriter Ribbon Manufactures 14 Cardboard Box Manufacturing 15 Carpenters, Wood Wool And Furniture Manufactures 16 Carpet And Druggist Factories 17 Cashew Nut Factories 18 Chemical Manufacturing 19 Cigar And Cigarette Factories 20 Coffee Grinding Premises 21 Coir Factories 22 Coir Carpets, Rugs And Tobacco, Hides And Skin Presses 23 Cold Storage Premises 24 Cork Products Manufacturing 25 Dry Cleaning, Dyeing And Laundries 26 Electric Generating Stations(Other Than Hydel) 27 Enamelware Factories 28 Filter And Wax Paper Manufacturing 29 Flour Mills 30 Garages 31 Garment Makers 32 Ghee Factories (Other Than Vegetable) 33 Godowns And Warehouses (Others) 34 Grain And/ Or Seeds Disintegrating And/or Crushing Factories 35 Grease Manufacturing 36 Hat And Topee Factories 37 Hosiery, Lace, Embroidery And Thread Factories 38 Incandescent Gas Mantle Manufactures 39 Industrial gas manufacturing including halogenated hydrocarbon gases. 40 Linoleum Factories. 41 Man-made Yard/Fiber Manufacturing (Except Acrylic). 42 Manure and Fertilizer Works (Blending, mixing and granulating only). 43 Mercantile Occupancies (Departmental Stores, Shopping Complexes of Malls). 44 Mineral Oil Blending and Processing 45 Museums. 46 Oil and Leather Cloth Factories 47 Oil Terminals/Depots other than those categorized under high hazard A. 48 Oxygen Plants. 49 Plywood Manufacturing/Wood Veneering Factories. 50 Paper and Cardboard Mills. 51 Piers, wharves, dockyards. 52 Plastic Goods Manufacturing. 53 Printing Press Premises. 54 Pulverizing and Crushing Mills. 55 Rice Mills. 56 Rope Works. 57 Rubber Goods Manufacturing. 58 Rubber Tyres and Tubes Manufacturing. 59 Shellac Factories. 60 Shopping Complexes (underground). 61 Silk filatures and cocoon stores. 62 Spray Painting. 63 Soaps and Glycerine Factories. 64 Starch Factories. 65 Steel Plants (Gas Based). 66 Tanneries/Leather Goods Manufacturers. 67 Tank farms other than those categories under high hazard A. 68 Textile Mills. 69 ea Factories. 70 Telephone Exchanges. 71 Theatres and Auditoriums. 72 Tobacco (Chewing) and pan-masala making. 73 Tobacco Grinding and Crushing. 74 Tobacco Re-drying Factories. 75 Woolen Mills. 3. HIGH HAZARD OCCUPANCIES Sub-Category-A: 1 Aircraft Hangers. 2 Aluminium/Magnesium Powder Plants. 3 Bituminised Paper and/or Hessian Cloth Manufacturing inducltrig Tar Felt Manufacturing. 4 Cotton Waste Factories. 5 Coal and/or Coke and/or Charcoal Ball Briquettes Manufacturing. 6 Celluloid goods manufacturing. 7 Cigarette filter manufacturing. 8 Cinema films and T.V. production studios 9 Collieries. 10 Cotton Seed Cleaning or De-lining Factories. 11 Distilleries. 12 Duplicating and Stencil Paper Manufacturing. 13 Fire-Works Manufacturing. 14 Foamed Plastics Manufacturing and/or Converting Plants. 15 Grass Hay, Fodder and Bhoosa (chaff). 16 Pressing Factories. 17 Jute Mills and Jute Presses. 18 LPG Bottling Plants (Mini)* (* Bottling plants having total inventory not exceeding 100 Metric Ton of Liquefied Petroleum Gas and also bottling a total quantity of not exceeding 20 Metric Ton of LPG per shift of 8 hours.) 19 Match Factories. 20 Man Made Fibers (Acrylic fibers/Yarn making). 21 Mattress and Pillow Making. 22 Metal or Tin Printers (where more than 50% of floor area is occupied as Engineering Workshop, this may be taken as Ordinary Hazard Risk). 23 Oil Mills. 24 Oil Extraction Plants (other than those forming part of ghee factories and oil refining factories). 25 Oil Terminals/Depots handling flammable liquids having flash point of 32 ° C and below. 26 Paints and Varnish Factories. 27 Printing Ink Manufacturing 28 Saw Mills. 29 Sponge Iron Plants. 30 Surgical Cotton Manufacturers. 31 Tank Farms storing flammable liquids having flash point of 32 ° C and below. 32 Tarpaulin and Canvas Proofing Factories. 33 Turpentine and Rosin Distilleries. 34 Tyre Retreading and Resoling Factories. Sub-Category-B 1 Ammonia and Urea Synthesis Plants 2 CNG Compressing and Bottling Plant 3 Explosive Factories 4 LPG Bottling Plants (other than Mini) 5 Petrochemical Plants 6 Petroleum Refineries
(b) Each trailer pump shall be provided with equipment as per Schedule II appended to this paragraph. Such equipment shall conform to the relevant Indian Standard.
(c) Trailer pumps shall be housed in a separate shed or sheds which shall be sited close to a principal source of water supplies in the vicinity of the main risks of the factory.
(d) In factories where the area is such as cannot be reached by man-hauling of trailer pumps within reasonable time vehicles with towing attachment shall be provided at the scale of one for every four trailer pumps with a minimum of one such vehicle kept available at all times. 118
(e) [The hydrant system should be distributed round the factory with due regard to potential fire risks at the factory. Where piped supply is provided, the size of the main shall not be less than 15 cm diameter and it shall be capable of supplying a minimum of 4,500 liters per minute at a pressure of not less than 7 kilograms per square cm. in case of light hazard occupancies. In case of high hazard area, the water pressure should be 10 kg. per square centimeter.
A certificate of completion from the installing engineer stating the pressure test to which the installation has been subjected and giving the dates from which it is in complete working order should also be submitted at the office of the inspector of Factories.
(f) All trailer pumps including the equipment provided with them and the vehicles for towing them shall be maintained in good condition and subjected to periodical inspection and testing as required.
Personnel in-charge of equipment and for fire fighting, fire drills, etc.
(a) The first-aid and other firefighting equipment to be provided as required in sub-paragraph (10) and (11) shall be in-charge of a trained responsible person.
(b) Sufficient number of persons shall be trained in the proper handling of firefighting equipment as referred to in clause (a) and their use against the types of fire for which they are intended to ensure that adequate number of persons are available for firefighting both by means of first-aid firefighting equipment and others. Such persons shall be provided with clothing and equipment including helmets, belts and boots, preferably gumboots. Wherever vehicles with towing attachment are to be provided as required in clause (d) of sub-paragraph (11) sufficient number of persons shall be trained in driving these vehicles to ensure that trained persons are available for driving them whenever the need arises.
(c) Fire fighting drills shall be held as often as necessary and at least once in every period of two months.
Automatic sprinkler and fire hydrants shall be in addition and not in substitution of the requirements in sub-paragraphs (10) and (1 1).
If the Chief Inspector is satisfied in respect of any factory or any part of the factory that owing to the exceptional circumstances such as inadequacy of water supply or infrequency of the manufacturing processor for any other reason, to be recorded in writing, all or any of the requirements of the rules are impracticable or not necessary for the protection of workers, he may by order in writing (which he may at his discretion revoke) exempt such factory or part of the factory from all or any of the provisions of the rules subject to conditions as he may by such order prescribe. 119
[Plan of fire-fighting installations showing the entire compound, whole buildings therein, within their doors and window openings, boundary walls, etc., should be submitted to the office of the Inspector of Factories, the State Fire Directorate and the local authority.] 120
61-A.Safety belts
Where any person is required or allowed to work at a place from which he may be liable to fall through a distance of more than two meters), he shall be provided with a safety 121 belt with leather shoulder straps of not less than [five centimeters] in width and a 'D' ring at the back for fastening a rope, the other end of which shall be securely tied or hooked to some suitable rigid fixture. The safety belt so provided shall be tested and examined thoroughly by a competent person at least once in six months and a certificate with regard to its suitability obtained from the said competent person and entered in a register, which shall be produced before the Inspector on demand.
122
61-AA.Safety officers. — ***
123
61-B.Ovens and driers
Application-This rule shall apply to ovens and driers, except those used in laboratories or kitchens of any establishment and those which have a capacity below 325 liters.
Definition-For the purpose of this rule, oven or drier means any enclosed structure, receptacle, compartment or box which is used for baking, drying or otherwise processing of any article or substance at a temperature higher than the ambient temperature of the air in the room or space in which the oven or drier is situated and in which a flammable or explosive mixture of air and a flammable substance is likely to be evolved within the enclosed structure, receptacle, compartment or box or part thereof on account of the article or substance which is baked, dried or otherwise processed within it.
Separate electrical connection-Electrical power supplied to every oven or drier shall be by means of separate circuit provided with an isolation switch.
Designs, construction, examination and testing
(a) Every oven or drier shall be properly designed on sound engineering practice and be of good construction, sound materials and adequate strength, free from any patent defects and safe if properly used.
(b) No oven or drier shall be taken into use in a factory for the first time unless a competent person has thoroughly examined all its parts and carried out the tests as arc required to establish that the necessary safe systems and controls provided for safety in operation for the process for which it is to be used and a certificate of such examination and tests signed by that competent person has been obtained and is kept available for inspection.
(c) All pans of an oven or drier which has undergone any alteration or repair which has the effect of modifying any of the design characteristics shall not he used unless a thorough examination and tests as have been mentioned in clause (b) has been carried out by a competent person and certificate of such examination and tests signed by that competent person has been obtained and is kept available for inspection.
Safety ventilation
(a) Every oven or drier shall be provided with a positive and effective safety ventilation system using one or more motor driven centrifugal fans so as to dilute any mixture of air and any flammable substance that may be formed within the oven or drier and maintain the concentration of the flammable substance in the air at a safe level of dilution.
(b) The sere level of dilution referred to in clause (a) shall be so as to achieve a concentration of the concerned flammable substance in air of not more than 25 per cent, of its lower explosive limit.
Provided that a level of concentration in air up to 50 per cent of the lower explosive limit of the concerned flammable substance may be permitted to exist subject to installation and maintenance of an automatic device which
(i) shows continuously the concentration of the flammable substance in air present in the oven or drier at any instant;
(ii) sounds an alarm when the concentration of the flammable substance in air in any part of the oven or drier, reaches a level of 50 per cent. of its lower explosive limit; and
(iii) shuts down the heating system of the oven or drier automatically when the concentration In air of the flammable substance in any part of the oven or drier teaches a level of 60 per cent. of its lower explosive limit, is provided to the oven or drier end maintained In efficient working condition.
(c) No oven or drier shall be operated without its safety ventilation system working in an efficient manner.
(d) No oven or drier shall be operated with a level of dilution less than what is referred to in clause (b).
(e) Exhaust ducts of safety ventilation system should be so designed and placed that their ducts discharge the mixture of air end flammable substance away from the work rooms and not near windows or doors or other openings from where the mixture could re-enter the work rooms.
(f) The fresh air admitted into the oven or drier by means of the safety ventilation system shall be circulated adequately by means of circulating fan or fans through all parts of the oven or drier so as to ensure that there are no locations where the flammable substance can accumulate in the air or become pocketed to any dangerous degree.
(g) Throttling dampers in any safety ventilation system should be so designed by cutting away a portion of the damper or otherwise, that the system will handle at least the minimum ventilation rate required for safety when they are set in their maximum throttling position.
Explosion panels
(a) Every oven or drier having an internal total space of not less than half cubic meter shall be provided with suitably designed explosion panels so as to allow release of the pressure of any possible explosion within the oven or drier through explosion vents. The area of openings to be provided by means of such events together with the area of opening; of any access doors which are provided with suitable arrangements for their release in case of an explosion, shall be not less than 2,200 square centimeters for every one cubic meter of volume of the oven or drier. The design of the explosion panels and doors as above said shall be such as to secure their complete release under an internal pressure of 0.25 kilogram per square centimeter.
(b) The explosion releasing panels, shall, as for as practicable, be situated at the roof of the oven or drier or at those portions of the walls where persons do not remain in connection with operation of the oven or drier.
Interlocking arrangements-In Bath oven or drier, efficient interlocking arrangements shall be provided and maintained to ensure that, -
(i) all ventilating fans and circulating fans whose failure would adversely affect the ventilation rate of flow pattern, are in operation before any mechanical conveyor that may be provided for feeding the articles or substances to be processed in the oven or drier is put into operation;
(ii) failure of any of the ventilating or circulating fans will automatically stop any conveyor as referred to in clause (I) as may be provided, as well as stop the fuel supply by closing the shut off valve and shut off the ignition in the cue of gas or oil fired ovens end in the case of electrically heated ovens switch off the electrical supply to the heaters;
(iii) the above said mechanical conveyor is set in operation before the above said shut off valve can be energized; end
(iv) the failure of the above said conveyor will automatically close the above said shut off valve in the case of ovens and driers heated by gas, oil or steam and deactivate the ignition system, or cut off the electrical heaters In the case of electrically heated ovens or furnaces.
Automatic Preventilation- Every oven or drier heated by oil, gas, steam or electricity shall be provided with an efficient arrangement for automatic pre-ventilation consisting of at least 3 volume changes with fresh air by operation of the safety ventilation fans and the circulating fans (if used so as to effect purging of the oven cc drier of any mixture of air and a flammable substance before the heating system can be activated and before the conveyor can be placed in position.)
Temperature control-Every oven or drier shall be provided with en automatic arrangement to ensure that the temperature within does not exceed a safe upper preset limit to be decided In respect of the particular processing being carried on.
Multi-stage processes-Wherever materials are to be processed in ovens or driers in successive operations, suitable arrangement should be provided to ensure that the operating temperatures necessary for safe operation at each stage are maintained within the design limits.
Combustible substances not to drip on electrical healers or burners flame-Effective arrangements shall be provided In every oven or drier to prevent dripping of combustible substances on electric heaters or burner flame used for heating.
Periodical examination, testing and maintenance
(a) All parts of every oven and drier shall be properly main- tamed and thoroughly examined end the various controls as mentioned in this rule and the waking of the oven or drier tested at frequent intervals to ensure its safe operation by a responsible person designated by the occupier or manager, who by his experience and knowledge of necessary precautions against risks el explosion, is fit to undertake such work.
(b) A register shall be maintained in which the details of the various tests carried out from time to time under clause (a) shall be entered and every entry made shall be signed by the person making the tests.
Training of operators-No person shall he assigned any task connected with operation of any oven or drier unless he has completed 18 years of age and he is properly trained.
Polymerizing machines
(a) Printed fabric shall be thoroughly dried by passing them over drying cans or through hot flue or other equally effective means before the same Is allowed to pass through polymerizing machines.
(b) Infra-red ray heaters of polymerizing machines shall be cut of 1 while running the prints.] 124
61-C.Fragile roofs
In any factory no person shall be required or allowed to stand on or pass over or walk on or near any roof or ceiling covered with fragile material through which he is liable to fall, in case it breaks or gives way, a distance of more than three meters, unless,
(i) suitable and sufficient ladders, duck ladders or crawling boards which shall be securely supported, arc provided and used; and
(ii) a permit to work on the fragile roof is issued to him each time he is required to work thereon, by a responsible person of the factory concerned, such as Supervisor, Foreman, Engineer or Manager.)
61D.Buildings and structures
No building, wall, chimney, bridge, tunnel, road, gallery, stairway, ramp, floor, platform, staging or other structure, whether of a permanent or temporary character, shall be constructed, situated or maintained in any factory in such a manner as to cause risk of bodily injury.
61E.Machinery and plant
No machinery, plant or equipment shall be constructed, situated, operated or maintained in any factory in such a manner as to cause risk of bodily Injury.
61F.Methods of work
No process or work shall be carried on in any factory in such a manner as to cause risk of bodily Injury.
61G Stacking and storing of materials, etc. No materials or equipment shall be stacked or stored in such a manner as to cause risk of bodily Injury. 125 61H [Special provisions regarding electricity [* * *] 126 61I [Ship building and Ship Repairing
(1) Application - These rules shall apply in respect of work carried out in ship building and ship repairing operations
(2) Definitions-In these rules, unless there is anything repugnant in the subject or context:
(i) "Certificate of entry" means a certificate which-
(a) is given by a person who is a competent analyst and who is competent to give such certificates; and
(b) certifies that he has in an adequate and suitable manner tested the atmosphere in the oil-tank or oil-tanks specified in the certificate and found that having regard to all circumstances of the case, including the likelihood or otherwise of the atmosphere being or becoming dangerous, entry to the oil-tank or oil-tanks without wearing breathing apparatus may in his opinion be permitted;
(ii) "hot work" means any work which involves
(a) welding, burning, soldering, brazing, sand blasting or chipping by spark producing tools; or
(b) use of non-flame proof electrical equipment or equipment with internal combustion engines; and includes any other work which Is likely to produce sufficient heat capable of igniting inflammable gases cc vapors.
(iii) "naked light certificate" means a certificate which
(a) is given by a person who is a competent analyst to give such certificates; and
(b) certifies that he has in an adequate and suitable manner tested for the presence of inflammable vapour the oil-tank compartment space or other part of the vessel specified in the certificate and found it to be free there from and that having regard to all the circumstances of the case, including the likelihood or otherwise of the atmosphere becoming inflammable, the use of naked lights. fires, lamps or heated rivets or any hot work to be carried out nay in his opinion be permitted In the oil-tank compartment, space or other part of the vessel specified in the certificate; o
(iv) "oil" means any liquid which has a flash point below 130 ° C (270 F) and also includes lubricating oils, liquid methane, liquid butane and liquid propane.
Explanation.- Flash paint whatever it occurs in these rules shall be flash point as determined by Abel Closed Cup or Prousky-Marten Closed Cup Procedures as described in I.S: 1448-1950.
(v) "Oil-tank" means any tank or compartment in which oil is or has been carried;
(vi) "The operations" means
(a) construction, reconstruction or breaking up of any ship or vessel, repairing, refitting, painting and finishing;
(b) the scaling, surfing or cleaning of its boilers (including combustion chambers or smoke boxes); and
(c) the cleaning of its bilges or oil-fuel-tanks or any of its tanks last used for carrying oil.
Explanation.-For the purpose of this clause, the expression ' oil' means oil of any description;
(vii) "Ship and vessel" have the same meanings as in the Merchant Shipping Act, 1958 (Central Act 44 of 1958);
(viii) "Shipyard" means any yard of dry dock (including the precincts thereof) in which ships or vessels are constructed, reconstructed, repaired, fitted or finished;
(ix) "Stage" means any temporary platform on or from which persons employed perform work in connection with the operations, but does not include a boatswain's chair;
(x) "Staging" includes any stage, any upright thwart, thwart pin, wedge, distance piece, belt or other appliance or material, not being part of the structure of the vessel, which is used in connection with the support of any stage, and any guard-rails connected with a stage;
(xi) "tanker" means a vessel constructed or adapted for carrying a cargo of oil in bulk.
(3) Access and staging: General access to vessels in a ship-yard - All main gangways giving general a:cess to a vessel in a shipyard, whether from the ground or from a wharf or quay, and all cross gangways leading from such a main gangway on to the vessel, shall
(a) be at least 60 cm wide;
(b) be securely protected on each side to a height of at least 90 cm. by strongly constructed upper and lower hand-rails and by a secure toe board projecting at least 15 c.m. above the floor;
(c) be a good construction, of sound material and adequate strength;
(d) be stable and wherever practicable, of permanent construction;
(e) be kept in position as long as required; and
(f) maintained in good repairs.
(4) Access to dry dock.
(i) Every flight of steps giving access from ground level either to an altar or to the bottom of a dry dock shall be provided throughout on each side with a substantial hand-rail. In the case of an open side, secure fencing to a height of at least 90cm. shall be provided by means of upper and lower rails, taut ropes or chains, or by other equally safe means. For the purpose of this sub-rule a flight of steps which is divided into two by chute for materials, with no space between either side of the chute and steps, shall be deemed to be one flight of steps.
(ii) Such hand-rails and fencings as aforesaid shall be kept in position save when and to the extent to which their absence is necessary (whether or not for the purposes of the operations), for the access of persons, or for the movement of materials or vessels or for traffic or working or for repair, but hand-rails or fencing removed for any of those purposes shall be kept readily available and shall be replaced as soon as practicable.
(5) Access to vessels in dry dock
(i) If a ship is lying in dry dock for the purpose of undergoing any of the operations, there shall be provided means of access for the use of workers at such times as they have to pass to, or from, the ship or dry dock
(a) where reasonably practicable, one or more ship's accommodation ladders; or
(b) one or more soundly constructed gangways or similar constructions.
(ii) The means so provided shall be not less than 55 cm. wide, properly secured and fenced throughout on each side to a clear height of 90 cm. by means of upper and lower rail:. taut ropes or chains or by any other safe means, except that in the case of the ship's accommodation ladder, such fencing shall be necessary on one side only, provided, where the other side is properly protected by the ship's side.
(iii) Where at any dry dock, there is a gangway giving access from an altar of the dock to a vessel which is in the dock for the purpose of undergoing any of the operations, and the edge of the altar is unfenced, adequate hand holds shall be available for full length of the altar which workers commonly use when passing between the gangway and the nearest flight of steps which gives access to ground level.
(6) Access to and from bulkwarks: Where there is a gang-way leading on to a bulkwark of a vessel there shall be provided a platform at the in-board end of the gangway with safe means of access there from to the decks:
Provided that such a platform is not practicable, a second gangway or stairway leading from a bulkwark on to the deck which are either attached to the first mentioned gangway or place contiguous to it, in which case means of access securely protected by fencing shall be provided from the one to the other.
(7) Access to staging, etc
(i) Whether outside staging is erected in a shipyard, there shall be provided sufficient ladders giving direct access to the stages having regard to the extent of the staging and to the work to be done.
(ii) Where a vessel is under construction or reconstruction and worker!. are liable to go forward or after a thwartship across or along uncovered deck- beams, or across or along floors, sufficient planks shall be provided on these deck-beams or on those floors for the purpose of access to or from places of work and sufficient and suitable portable ladders shall be provided so as to give access either from the ground or outer bottom plating to the top of the floor.
(iii) Without prejudice to any other provision contained in clause (ii) of sub-rule
(5) requiring greater width, no footway or passageway, constructed of planks shall be less than 45 cm. wide.
(8)
(i) Subject to clauses (ii) and (iii) of this sub-rule, every ladder which affords a means of access, communication or support to person shall
(a) be soundly constructed and properly maintained;
(b) be of adequate strength for the purpose for which it is used; and
(c) be securely fixed either
(i) as near its upper resting place as possible; or
(ii) where this is impracticable at its base, or where such fixing is impracticable. a person shall be stationed at the base of the ladder when in use to prevent it from slipping; and
(d) Unless there is other adequate hand-hold, extend to a height of at least 75 cm. above the place of landing or the height of the highest rung to be reached by the foot of any person working on the ladder, as the case may be or, if this is impracticable, to the greatest practicable height.
(ii) Requirements of sub-clauses (c) and (d) of clause (i) above shall not apply to fixed ladders of a ship or to rope ladders. Effect's e measures by means of roping off or other similar means shall be taken to prevent the use of fixed ladders of a ship which do not comply with requirements of sub-clauses (a) and (b) of clause (i) above.
(iii) Any worker who removes any ladder and acts it up in a new position shall, as regards that ladder, comply with requirements of sub-clause (c) of clause (i) above.
(iv) Rope ladders shall provide foothold of a depth including any space behind the ladder of not less than 12 cm. and suitable provisions shall be made for preventing such ladders from twisting.
(9) Lashing of ladders
(i) A fiber rope, or a rope made with strands consisting of wire cores covered with fiber, shall not be used to secure a ladder used for the purpose of the operations.
(ii) A wire rope shall not be used to secure any such ladder unless its ends are forruled, but this provision shall not apply in the case of an end which is so situated or protected that a person using the ladder is not liable to come into contact with it so as to suffer injury.
(10) Material for staging
(i) A sufficient supply of sound and substantial material and appliances shall be available in convenient place or places for the construction of staging.
(ii) All planks and other materials and appliances intended to be used or re-used for staging shall be carefully examined before being taken into use or re-use in any staging. Every examination required by this clause shall be carried out by a person competent for the purpose.
(11) Maintenance of staging, dry dock altars and shoring sills
(i) All staging ’ s and every part thereof shall be of good construction, of suitable and sound materials and of adequate strength for the purpose of which it is used and shill be properly maintained, and every upright and thwart shall be kept so fixed, secured or placed in position as to prevent accidental displacement.
(ii) All planks forming stages shall be securely fastened to prevent them from slipping unless they extend 45 cm. or more beyond the inside edge of the thwart or support on which they rest.
(iii) All staging used in connection with the operations shall be inspected before use, and thereafter at regular and frequent intervals, by a responsible person.
(iv) All dry dock altars and shoring sills on or from which persons perform work in connection with the operations shall be of sound construction and properly maintained.
(v) All parts of stages, all parts of footways or passage-ways constructed of planks, and all parts of the dry dock altars or shoring sills, being parts on nr from which persons perform work in connection with the operations, shall be kept clear of all substances likely to make foot-hold or handhold insecure.
(12) Using of upright for hoisting block
(i) If any upright forming part of staging is used as a fixing for a pulley block for hoisting materials
(a) it shall be properly housed in the ground or shall otherwise be adequately secured so as to prevent it from rising; and
(b) it shall be suitably protected against damage by the action of the chain or wire or other means of securing the pulley block to the upright.
(ii) No upright forming part of staging shall be used as an anchorage for a load pulley block, unless the upright is not likely to be displaced by such use.
(13) Support of stages on planks: Planks supported on the rungs of ladders shall not be used to support stages.
(14) Maintenance of suspended stages
(i) Stages suspended by ropes or chains shall be secured as far as possible so as to prevent them from swinging.
(ii) A fiber rope, or a rope made of strands consisting of wire cores covered with fiber, shall not be used for suspending a stage except that fiber ropes may be used in the use of a stage of which the suspension ropes are received through blocks.
(iii) Chains, ropes, blocks and other gear used for the suspension of stages shall be of sound material, adequate strength and suitable quality, and in good condition.
(iv) Appropriate steps shall be taken to prevent ropes or chains used for supporting a stage from coming into contact with sharp edges of any part of • vessel.
(15) Provision of Boatswin's Chairs
(i) Boatswain's chairs and chains ropes or other gear used for their suspension shall be of sound materials, adequate strength and suitable quality and the chains, ropes or other gear shall be securely attached.
(ii) Suitable measures shall be taken to prevent where possible the spinning of a boatswain's chair to prevent the tipping of a boatswain's chair and to prevent any occupant falling there-from.
(16) Rising stages All planks forming a rising stage at the bow end of a vessel shall be securely fastened to prevent them from slipping.
(17) Width of staging- Without prejudice to the other provisions of this rule all stages shall be sufficient width as is reasonable in all the circumstances of the case to secure the safety of the persons working thereon.
(18) Maintenance of stage: from which a person is liable to fall more than 2 m or into water while working
(i) This sub-rule applies to stages from which a person is liable to fall a distance of more than 2 m. or into water in which there is a risk of drown-ins while working.
(ii) Every stage to which this sub-rule applies
(a) if it is not a side immediately adjacent to any part of a vessel,
(b) shall be so constructed or placed that a person is not liable to fall while working as aforesaid through a gap in the staging not being a gap necessary and having regard to the nature of the work being carried on;
(c) shall be at least 45 cm. on wide.
(iii) Every side of a stage to which this sub-rule applies shall
(a) if it is not a side immediately adjacent to any part of a vessel, be fenced subject to the provisions of clauses (iv) to (vii) of this sub-rule, with a guard rail or guard rails to a height of at least I m. above the stage, which rail or rails shall be so placed as to prevent the fall of persons from the stage or from any standing raised standing place on the stage; or
(b) if it is a side immediately adjacent to any part of vessel, be placed to that part having regard to the nature of the work being carried on and to the nature of the structure of the vessel.
(iv) in the case of stages which are suspended ropes or chains, and which are used solely for painting, the fencing required by sub-clause (a) of clause (iii) of this sub-rule may be provided by means of taut guard rope or taut guard ropes.
(v) No side of a stage or, as the case may be. no part of the side of a stage need be fenced in pursuance of sub-clause (a) of clause (iii) of this sub-rule in cases where and so long as, the nature of the work being carried on makes the fencing of that side, or, as the case may be, that part impracticable.
(vi) Guard rails provided in pursuance of sub-clause (a) of clause (iii) of this sub rule may he removed for the access of persons or for the movement of materials only and replaced immediately.
(vii) Where it is not reasonably practicable to comply with the provisions of sub- clause (a) of clause (iii) of this sub-rule, workers shall be provided with suitable safety belts equipped with life lines which are secured with a minimum amount of slack to a fixed structure. Further precautions against fall of persons, materials and articles
(19) Fencing of dry docks
(i) Fencing shall be provided at or near the edges of a dry dock at ground level, including edges above flights of steps and chutes for materials. The height of such fencing shall a; a no point be less than I m.
(ii) Such fencing as aforesaid shall be kept in position safe when and to the extent to which its absence is necessary (whether or not for the purposes of the operations) for the access of persons, or for movement of materials or vessels or for traffic or working, or for repair, but fencing removed for any of these purposes shall be kept readily available and shall be replaced immediately.
(20) Protection of openings
(i) Every side or edge of an opening in a dock or tank top of a vessel being aside or edge which may be a source of danger to workers shall, except where and while the opening is securely covered or where the side or edge is protected to a height of not less than 75 cm by a coaming or other part of the vessel, be provided with fencing to a height of not less than 90 cm above the edge of side and such fencing shall be kept in position save when and to the extent to which its absence is necessary (whether or not for the purposes of the operations), for the access of persons. or for the movement of materials, or for traffic or working, or for repair, but fencing removed for any of these purposes shall be kept readily available and shall be replaced as soon as practicable.
(ii) Clause (i) above shall not apply
(a) to that part of an opening in a deck or tank top which is at the head of a stairway or ladder-way intended to be used while the operations are being carried on; or
(b) to parts of a deck or tank top which are intended to be plated, except such parts where the plating has necessarily to be delayed so that the opening may be used for the purpose of the operations.
(21) Fall of articles front stages- Where workers are at work outside a vessel on stage adjacent to part of the structure of the vessel and other workers are at work dimity beneath that stage, the planks of the stage shall be in such a position that no article liable to cause injury to the workers can fall between the planks and the inside plank of the stage shall be placed as near as practicable to the structure of the vessel having regard to the nature of the work being carried on.
(22) Provision of boxes for rivets, etc
(i) Boxes or other suitable receptacles for rivets, nuts, bolts and welding rods shall be provided for the use of workers.
(ii) It shall be the duty of the workers to use so far as practicable the boxes or other suitable receptacles so provided.
(23) Prohibition of throwing down materials and articles
(i) Subject to the provision of clause of this sub-rule, parts of staging, tools and other articles and materials shall not be thrown down from a height where they are liable to cause injury to workers but shall be properly lowered.
(ii) When the work to be done necessarily involves the throwing down from a height of articles or materials, conspicuous notice shall be pasted to warn persons from working or passing underneath the place from which articles or materials may fall and the work shall be done under the direct supervision of a supervisor in charge of the work.
(iii) No person shall throw down any articles or materials from height except in accordance with the requirements of this sub-rule.
(24) Rising of loose articles or materials- So far as practicable, steps shall be taken to minimize the risk arising from loose articles or materials being left lying about in any place from which they may fall on workers or persons passing underneath. Raising and Lowering
(25) Precaution for secureness of loads
(i) Loads shall be securely suspended or supported whilst being raised or lowered, and all reasonable precautions shall be taken to prevent danger from slipping or displacement.
(ii) Where by reasons of the nature of position of the operations load is liable, whilst being moved by a lifting machine or lifting tackle, to come into contact with any object so that the object may became displaced, special measures shall be adopted to prevent the danger so far as reasonably practicable.
(26) Support of lifting machinery and lifting tackle Every lifting machine and all lifting tackles shall be adequately and suitably supported or suspended having regard to the purpose for which it is used.
(27) Wire ropes with broken wires No wire rope shall be used if in any length of ten times the diameters of the wire rope the total number of visible broken wires exceeds five percent of the total number of wires, or if the rope shows signs of excessive wear or corrosion or other serious defect.
(28) Splices in wire ropes A thimble or loop splices made in any wire rope shall have at least three tucks with a whole strand of the rope and two tucks with one half of the wires cut out of each strand. All tucks shall be against the lay of' the rope:
Provided that this sub-rule shall not operate to prevent the use of another form of splice which can be shown to be as efficient as the form of splice specified in this sub-rule.
(29) Restriction in the use of knotted chains, etc
(i) No chain or wire rope shall be used when there is a knot tied in any part thereof.
(ii) No chain which is shortened or joined to another chain by means of bolts and nuts shall be used:
Provided that this does not exclude the use of a chain bolted or joined to another chain by an approved and properly constructed attachment.
(30) Precautions against damage to chains and wire ropes Appropriate steps shall be taken to prevent so far as practicable, the use of chains or wire ropes for raising or lowering in circum-stances in which they are in or liable to come into contact with sharp edges of plant, materials or loads, or with sharp edges of any part of the vessel on which work is being carried on.
(31) Loads on lifting appliances No load shall be left suspended from a lifting appliance other than a self sustaining, manually operated lifting appliance unless there is competent person in charge of the appliance while the load is so left.
(32) Ascertaining the weights of heavy loads Where there is reason to believe that a load being lifted or lowered on a lifting appliance weighs more than 20 tonnes, its weight shall be ascertained by means of an accurate weighing machine or by the estimation of a person competent for the purpose, and shall be clearly marked on the load:
Provided that this sub-rule shall not apply to any load lifted or lowered by a crane which has either a fixed or a derricking jib and which is fitted with an approved type of indicatory in good working order which
(a) indicates clearly to the driver or person operating the crane when the load being carried approaches the safe working load of the crane for the radius of the jib at which the load is carried; and
(b) gives an efficient sound signal when the load moved is in excess of the safe working load of the crane at that radius. Precautions against asphyxiation, injuries, fumes or explosions
(33) Certification for entry into confined spaces A space shall not be certified under section 36 (3) (a) of the Act unless
(a) effective steps have been taken to prevent, any ingress of dangerous fumes;
(b) any sludge or other deposit liable to give off dangerous fumes has been removed and the space contains no other material liable to give off dangerous fumes; and
(c) the space has been adequately ventilated and tested for dangerous fumes and has a supply of air adequate for respiration; but no account shall be taken for the purposes of clause (b) of this sub-rule of any deposit or other material liable to give off dangerous fume in insignificant quantities only.
(34) Precautions against shortage of oxygen No person shall enter or remain in any confined space in a vessel, being a confined space in which there is reason to apprehend that the proportion of oxygen in the air is so low as to involve risk of persons being overcome, unless either
(a) the space has been and remains adequately ventilated and a responsible person has tested it and certified that it is safe for entry without breathing apparatus, or
(b) he is wearing a suitable breathing apparatus and a safety belt securely attached to a rope, the free end of which is held by a person standing outside the confined space.
Explanation. — "a responsible person" means a supervisory personnel who is competent to test the confined space and issue a certificate.
(35) Restriction for the use of rivet fires-
(i) Rivet fires shall not be taken into or used in or remain in any confined space on board or in a vessel unless there is adequate ventilation to prevent the accumulation of fumes.
(ii) No person employed shall move a rivet fire into any confined space on board of in a vessel unless he has been authorised by his employer to move the fire into that space.
(36) Use of gas cylinders and acetylene generators
(i) No cylinder which contains or has contained oxygen or any inflammable gas or vapour at a pressure above atmospheric pressure and no acetylene generating plant, shall be installed or placed with 5 m. of any substantial source of heat (including any boiler or furnace when alight) other than the burner or blow pipe operated from the cylinder or plant.
(ii) No such cylinder and no such plant shall be taken below the weather deck in the case of a vessel undergoing repair, or below the topmost completed deck in the case of a vessel under construction, unless it is installed or placed in a part of the vessel which is adequately ventilated to prevent any dangerous concentration of gas or fumes.
(37) Restriction in the use of acetylene generators
(i) The following shall be observed as respects any acetylene generating plant
(a) no such plant shall be installed or placed in an) confined space unless effective and suitable provision is made for securing and maintaining the adequate ventilation of that space so ac to prevent, so far as practicable, any dangerous accumulation of gas;
(b) any person attending or operating any such plant shall have been fully instructed in its working and copy of the maker's instructions for that type of plant shall be constantly available for his use;
(c) the charging and cleaning of such plant shall so far as practicable be done during daylight;
(d) partly spent calcium carbide shall not be recharged into an acetylene generator.
(ii) No person shall smoke or strike a light or take a naked light or a lamp in or into any acetylene generator house or shed or in or into dangerous proximity to any acetylene generating plant in the open air or on board a vessel:
Provided that this clause shall not apply as respects a generator in the open air or on board a vessel which since it was last charged, has been thoroughly cleaned and freed from any calcium carbide and acetylene gas.
(iii) A prominent notice prohibiting smoking, naked lights and lamps shall be exhibited on or near every acetylene generating plant whilst it is charged or is being charged or is being cleaned.
(38) Use of proper apparatus for cutting, welding or heating metal
(i) Pipes or hoses for the supply of oxygen or any inflammable gases or vapour to any apparatus for cutting, welding or heating metal shall be of good construction and sound material and be properly maintained.
(ii) Such pipes or hoses shall be securely attached to the apparatus and other connections by means of suitable clips or other equally effective appliances.
(iii) Efficient reducing and regulating valves for reducing the pressure of the gases shall be provided and maintained in connection with all cylinders containing oxygen or any inflammable gases or vapour at a pressure above atmospheric pressure while the gases or vapors from such cylinders are being used in any process of cutting, welding or heating metal.
(iv) Where acetylene gas is used for cutting, welding or beating metal
(a) properly constructed and efficient back-pressure valve and flame arrester shall be provided and maintained in the acetylene supply pipe between each burner or blow-pipe pod the acetylene generator, cylinder or container from which it is supplied and shall be placed as near as practicable to the burner or blow-pipe except that those requirements shall not apply where an acetylene cylinder serves only one burner or blow pipe; and
(b) any hydraulic valves provided in pursuance of sub-clause (a) of clause (iv) shall be inspected on each day by every person who uses the burner or blow-pipe on that day and it shall be the duty of every worker who used the burner or blow-pipe to inspect the hydraulic valve accordingly
(v) The operating valves of burners or blow-pipes to which oxygen or any inflammable gases or vapour is supplied for the purpose of cutting, welding or heating metal shall be so constructed, or the operating mechanism shall be so protected that the valves cannot be opened accidentally.
(39) Precaution after use of apparatus for cutting, welding or heating metal
(i) In the case of apparatus on board a vessel and used for cutting, welding or heating metal with the aid of oxygen or any inflammable gas or vapour supplied at a pressure above atmospheric pressure, the precautions specified in this sub-rule shall be taken when such use ceases for the day or for a substantial period and the apparatus is to be left on board, but need not be taken when such use is discontinued merely during short interruptions of work. The requirements in clauses (iii) and (iv) of this sub-rule shall not apply during a meal interval, provided that a responsible person is placed in charge of the plant and equipment referred to therein.
(ii) Supply valves of cylinders, generators and gas mains shall be securely closed and the valve key shall be kept in the custody of a responsible person.
(iii) Movable pipes or hoses used for conveying oxygen or inflammable gas or vapour and the welding and cutting torches, shall, in the case of a vessel undergoing construction, be brought to the topmost completed deck, or in the case of a vessel under-going repair, to a weather deck or in either case to some other place of safety which is adequately ventilated to prevent any dangerous concentration of gas or fumes:
Provided that where, owing to the nature of the work, it is impracticable to comply with the foregoing requirements of this clause, the pipes or hoses shall be disconnected from cylinders, generators or gas mains, as the case may be.
(iv) When cylinders or acetylene generating plant have been taken below deck as permitted by clause (ii) of sub-rule (36). Such cylinders or acetylene generating plant shall be brought to a weather deck or, in the case of a vessel undergoing construction to the topmost completed deck.
(40) Naked lights and hot works on oil-carrying vessels
(i) Subject to the provisions of clause (ii) of this sub-rule and to the provisions of sub-rule (48) and without prejudice to the provisions of sub-rules (46) and (47), no naked light, fire or lamp (other than a safety lamp of a type approved for the purpose of this sub-rule:
(a) shall be permitted to be applied to, or to be in, or any hot work permitted to be carried out in any part of a tanker. unless a naked light certificate has been obtained and is in force in respect of these parts of the tanker for which, in the opinion of a competent analyst, a naked light certificate is necessary:
Provided that a-naked light, fire or lamp of a kind specified by a competent analyst may be applied to or be in. or any hot work of a type specified by him carried on, in any part of the tanker so specified,
(b) shall be permitted
(i) to be in any oil teak on board or in a vessel in which oil tank the oil last carried was having a flash point of less than 23 ° C (75 F) or was liquid methane, liquid propane or liquid butane;
(ii) to be applied, to the outer surface of any oil tanker on board or in a vessel in which oil-tank the oil last carried was such oil as aforesaid or any work of such a nature which is likely to produce sufficient heat capable of lighting inflammable gases or vapors permitted to be carried out, on the outer surface of such oil tank or vessel, unless a naked light certificate has previously been obtained on the same day and is in force in respect of that oil tank
(iii) to be applied to the outer surface of, or to be in, any compartment or space adjacent to an oil-tank on board or in a vessel to which oil tank the oil last carried was such oil as aforesaid, or any hot work permitted to be carried out in such compartment or space as aforesaid, or any work of such nature which is likely to produce sufficient heat capable of igniting inflammable gases or vapors, permitted to be carried out on the outer surface of such compartment or space, unless naked light certificate has previously been obtained on the same day and is in force in respect of that compartment or space:
Provided that where in any such case referred to in items (i), (ii) and (iii) of this clause a competent analyst has certified that daily naked light certificates are unnecessary or are necessary only to a specified extent such a daily certificate need not be obtained or as the case may be, need only be obtained to the specified extent;
(c) shall be permitted to be applied to the outer surface of, or be in, any oil- tank on board or in a vessel or any hot work permitted to be carried out in any such oil-tank or vessel or any work of such nature which is likely to produce sufficient heat capable of igniting inflammable gases or vapors, permitted to be carried out on the outer surface of the oil-tank or vessel, unless, since oil was last carried in that oil-tank, a asked light certificate has been obtained and is in force in respect of that oil-tank;
(d)
(i) shall be permitted to be applied to the outer surface of, or to be in, any compartment or space adjacent to an oil-tank on board or in a vessel or any hot work permitted to be carried out In any such compartment or space or any work of such nature which is likely to produce sufficient heat capable of igniting inflammable gases or vapors, permitted to be carried out on the outer surface of any such compartment or space, unless, since oil was last carried as cargo in that oil-tank. a naked light certificate has been obtained and is in force in respect of that compartment Of space.
(ii) Notwithstanding anything in clause (i) of this sub-rule, heated rivets may be permitted in any place without naked light certificate being in force in respect of that place if expressly so authorised by a competent analyst who certifies that after adequate and suitable testing, he is satisfied having regard to all the circumstances of the atmosphere becoming case including the likelihood or otherwise of the atmosphere becoming flammable that the place is sufficiently fret from flammable vapour, but such heated rivets shall where practicable, be passed through tubes.
(iii) No person shall introduce, have or apply naked light, fire or lamp (other than safety lamp of a type approved for the purpose of this rule) into, in or to any place where they are prohibited by this rule.
(iv) No person shall carry out hot work or any work of such nature which is likely to produce sufficient heat capable of igniting inflammable gases or vapors, in any place or any surface where they are prohibited by this rule.
Explanation: 'Competent analyst' means an analyst who is competent to give a naked light certificate.
(41) Restrictions for entering oil-tanks
(i) No person (other than an analyst entering with a view to issuing a certificate of entry) shall, unless he is wearing a breathing apparatus of a type approved for the purpose of this sub-rule, enter or remain in an oil-tank on board or in a vessel unless, since the oil-tank last contained oil, a certificate of entry has been obtained and is in force in respect of the tank.
(ii) Without prejudice to clause (i) of this sub-rule. no person (other than an analyst entering as aforesaid) shall be allowed or required to enter or remain in an oil-tank, on board or in a vessel in which oil-tank the oil last carried was oil having a flash point of less than 23 ° C (73 ° F) unless since the oil-tank last contained oil, an analyst has certified that the atmosphere is sufficiently free from inflammable mixture.
(iii) The provisions of this sub-rule are without prejudice to the requirement of sub-rule (34).
(42) Duration of Certificate - Any naked light certificate or certificate of entry may be issued subject to a condition that it shall not remain in force after a time specified in the certificate.
(43) Posting of Certificates - Every occupier for whom a naked light certificate or a certificate of entry is obtained shall ensure that the certificate or a duplicate thereof is posted as soon as may be and remains posted in a position where it may be conveniently read by all persons concerned.
(44) Maintaining safe atmosphere-
(i) When conditions in an oil-tank are such in respect of which a naked light certificate has been issued that there is a possibility of oil vapour being released from residues or other sources, test shall be carried out by a competent analyst at such intervals as may be required so as to ensure that the conditions in the tank are maintained safe.
(ii) Whenever hot work is carried on or naked light, fire or lamp is allowed to be, on the weather deck over spaces, in respect of which a naked light certificate has not been issued, all Covers of manholes and openings on deck and all valves (except those which are connected to high vent pipes) connecting the weather deck with the said spaces, shall be closed.
(iii) A record of all the tests carried out for the purpose of sub-rules (34), (40) and
(41) shall be maintained in a register which shall furnish the date, time, locations and results of the tests.
(45) Cleaning of oil-tanks
(i) Subject to the provisions of sub-rule (48), before a test for flammable vapour is carried out with a view to the issue of a naked light certificate for the purposes of sub-rule (40) in respect of an oil-tank on board or in a vessel, that oil-tank shall, since oil was last introduced into the tank, be cleaned and ventilated in accordance with clause (ii) of this sub-rule.
(ii) The said cleaning and ventilation shall be carried out by the following methods
(a) the oil-tank shall be treated in such manner and for such period as will ensure the vaporization of all volatile oil;
(b) all residual oil and any sludge or other deposit in the oil-tank shall be removed therefrom; and
(c) after the oil-tank has been so cleaned
(i) all covers of manholes and other openings therein shall be removed and it shall be thoroughly ventilated by mechanical or other efficient means with a view to the removal of all oil vapour; and then
(ii) the interior surfaces, if any deposit remains thereon shall be washed or scraped down.
(46) Invalidation of certificates
(i) If during the course of work in, or to the other surface of, any part of a tanker or air-craft carrier, any pipe or tank joint is opened or broken or any other event occurs so that there is a risk of oil vapour entering or arising in that part of the tanker or aircraft carrier, that work shall be suspended and thereafter any certificate or entry previously issued in respect of any oil-tank in that part and any naked light certificate previously issued in respect of that part shall be no longer in force.
(ii) If (in the case of a vessel other than a tanker or air-craft carrier) during the course of work, in any oil-pipe or in any compartment or space adjacent thereto, any pipe or tank joint is opened or broken or any other event occurs so that there is risk of oil vapour entering or arising in the oil-tank or in any compartment or space adjacent thereto shall be suspended and thereafter any certificate of entry previously issued in respect of the oil-tank, and any naked light certificate previously issued in respect of the oil-tank, or any compartment or space adjacent thereto shall be no longer in force.
(47) Provisions as to work in other compartments of spaces
(i) Without prejudice to the other provisions of these sub-rules, if the presence of oil in such quantity and in such position as to be likely to give rise to fire or explosion is detested in any part of a vessel, being a part to which this rule applied and in which repairs of the following kind are to be or are being undertaken that is to say, repairs involving the use of a naked light, fire (sic.) purpose of sub-rule (40) or involving hot work, such repairs shall not be started or continued until a naked light certificate has been issued or, as the case may be misused in respect of that part of the vessel.
(ii) This rule shall apply to bilges, shaft, tunnels, pump-rooms, lamp rooms, and to compartments and spaces other than those to which clause (i) (d) of sub-rule
(40) applies.
(48) Exemption — If the Chief Inspector is satisfied, by reasons of the nature of the work and the circumstances in which it is carried out, that any provisions of sub-rules (33) to (45) or part thereof can be suspended or relaxed without dangers to the health or safety of any person, be may grant suspension or relaxation in writing specifying such conditions as he may consider fit. Any such suspension or relaxation may be revoked at any time. Precautions In Use Of Electrical Energy
(49) Electric energy other than that generated by an independent generating unit on board shall not be taken for use, or used in, or in connection with any of the operations unless the body of the ship is securely earthed in such a manner as to ensure an immediate and safe discharge of energy to the earth. A ship or vessel shall not be considered as securely earthed for the purpose of this sub-rule only on account of it being partly submerged in water.
(50)
(i) Electric or welding shall not be carried on in connection with any of the operations unless separate and fully insulated welding return conductor or conductor as the case may be of adequate electrical capacity are provided for return of the current to the transformer or generator of the welding set:
(ii) The return end of the source of the welding current shall not be earthed;
(iii) All work on which welding is carried on shall be securely earthed independently to an earth electrode by means of conductor or conductors as the case may be, of adequate capacity, unless all such work are connected to any structure of the ship or vessel in such a manner as to ensure adequate connection to earth as aforesaid.
(51) Cutting of energy In certain cases - Electric energy shall be cut off from all portable electric tools and manual electrode holders within any tank, compartment or space referred to in sub-rules (34) and (40) or in any other confined space during all times when such toots or holders are not in operation:
Provided that for determining whether any such portable electric tool or electrode holder is not in operation, no account shall be taken of brief interruptions of work occurring during normal working:
Provided further that energy may not be cut-off from any such equipment if a responsible person is left in charge of it in such tank, compartment or space concerned:
Provided also that cutting of all electrical energy by 'operation of any switch or control provided on the portable tool or electrodes holder itself should not be taken as fulfilling the requirement of this sub-rule. Miscellaneous Safety Provisions
(52) Provisions of sufficient light - All parts of a vessel and all other places where the operations are being carried on, and all approaches to such parts and to places to which a worker may be required to proceed in the course of his employment, shall be sufficiently and suitably lighted. In providing such lighting due regard shall be given to avoidance of glare and formation of shadow, to the safety of the vessel and cargo, of the navigation of other vessels, and to any local statutory requirements as to the lighting of the harbor or deck.
(53) When work shall be permitted in boilers, etc.
(i) No work shall be permitted in any boiler, boiler furnace or boiler-flue until it has been sufficiently cooled to make work safe for the workers.
(ii) Before any worker enters any steam boiler which is one or a range of two or more steam boilers
(a) all inlets through which steam or hot water might otherwise enter the boiler from any other part of the range shall be disconnected from that part, or
(b) all valves or taps controlling such entry shall be closed and securely locked.
(iii) While workers remain in any steam boiler to which clause (ii) of this sub-rule applies all such inlets as are referred to in that sub-rule shall remain disconnected or all such valves or taps as are therein referred to shall remain closed and securely locked.
(iv) No worker shall be allowed or required to enter or remain in and no person shall enter or remain in, any steam boiler to which clause (ii) of this sub-rule applies unless the provisions of that sub-rule are being complied with.
(54) The hatch beams of any hatch in use for the operations shall, if not removed, be adequately secured to prevent their displacements.
(55) Bolts which have been jumped-up and re-screwed shall not be used for securing plates on the sides of vessels, and no worker shall use such bolts for this purpose.
(56) Work In or on life boats
(i) Before workers are permitted to work in or on any life boat, either steward or in suspended position, precautions shall be taken to prevent the boat from falling due to accidental tripping of the releasing gear' or movement of the davits, and capsizing of the boat if in checks.
(ii) Workers shall not be permitted to remain in life boats while the life boats are being hoisted into final steward position. Protection Wear
(57) Hand Protection - Adequate protection for the hands shall be available for all workers when using cutting or welding apparatus to which oxygen or any flammable gas or vapour is supplied at a pressure greater than atmospheric pressure or when engaged in machine caulking or machine reveling or in transporting or stacking plates or in handling plates at machines.
(58) Protection In connection with cutting or welding
(i) Suitable goggles fitted with tinted eye pieces shall be provided and maintained for all persons employed when using cutting or welding apparatus to which oxygen or any flammable gas or vapour is supplied at a pressure above atmospheric pressure.
(ii) There shall be provided and maintained for the use of all persons employed when engaged in the process of electric welding
(a) suitable helmets or suitable head-shields or suitable hand shields to protect the eyes and face from hot metal and from rays likely to be injurious; and
(b) suitable gauntlets to protect the hands and fore-arms from bet metal and from rays likely to be injurious.
(iii) When electric welding is in progress at any place and persons other than those enraged in that process are employed in a position where the rays are likely to be injurious to their eyes, screens shall be provided at that place for the protection of these persons: Provided that when it is not possible to provide screen, suitable goggles shall be provided for their use.
(59) Eye protection for other processes - Suitable goggles of effective screens shall be provided to protect the eye of all workers in any of the following processes:
(a) the cutting out or cutting off of cold rivets bolts from boilers or other plant or from ships;
(b) the chipping, scaling or scaling of boilers or ships plates;
(c) drilling by means of portable machine tools;
(d) dry grinding of metals.
(60) Head Protection - When workers are employed in areas where there is danger of falling objects they shall be provided with suitable safety helmets.
(61) Provision of safety belts and life-lines
(i) Whenever any worker is engaged on work at a place from which he is liable to fall more than 2 (two) m. he shall be provided with safety belts equipped with lifelines which are secured with a minimum of slack, to a fixed structure unless any other effective means such as provision of guard rails or ropes are taken to prevent his falling.
(ii) All safety belts and lifelines shall be examined once in six months by a competent person to ensure that no belt or lifeline which is not in good condition is used. Health And Welfare
(62) Prohibition of employment of young persons in certain process
(1) No young person shall be employed in
(a) the application of asbestos by means of a spray; or
(b) the breaking down for removal of asbestos lagging; or
(c) the cleaning of sacks or other containers which have contained asbestos; or
(d) the cutting of materials containing asbestos by means of portable power-driven saws; or
(2) the scaling, scurfing or cleaning of boilers, combustion chambers or smoke boxes, where his work exposes him to dust of such a character and to such an extent as to be likely to be injurious or offensive to persons employed in such work.
(63) Restriction in the use of lead
(i) Lead paint shall not be applied in the form of a spray in the interior painting of any part of a ship or vessel
(ii) Wherever lead sheathing work is carried on for making cold storage chambers in the ships, efficient exhaust droughts with portable extractors should be provided to remove the lead fumes from the confined spaces.
(64) Provision of stretchers, ambulances and ambulance rooms, etc.
(i) In every shipyard, there shall be provided and kept readily available
(a) at least two numbers of suitably constructed sling stretchers or other similar appliances for raising injured persons;
(b) at least two numbers of carrying or wheel stretchers;
(c) at least two numbers of suitable reviving apparatus and oxygen and the stretchers, appliances and apparatus so provided shall be properly maintained.
(ii) In every shipyard, there shall always be readily available during working hours a responsible person or responsible persons whose duty it is to summon an ambulance or other means of transport if needed in cases of accident or illness. Legible copies of a notice indicating that person, or as the case may be these persons shall be affixed in prominent positions in every shipyard.
(iii) In every shipyard other than a dry dock available for hire-
(a) in which the number of persons employed normally exceeds five hundred; or
(b) in which the number of persons employed normally exceeds one hundred and which is more than ten miles from a hospital there shall be provided and maintained in good order and in clean condition a properly constructed ambulance room containing at least the equipment as prescribed in the rule 64 of the Tamil Nadu Factories Rules, 1950. The room shall be used only for the purpose of treatment and rest and shall be in charge of a suitably qualified person who shall be readily available during working hours, and record shall be kept of all cases of accident or sickness treated at the room.
(65) Restrictions In the employment of young persons
(i) No young person shall until he has been employed in a shipyard or shipyards for at least six months be employed in connection with the operations in a shipyard on stage from which, or in any part of a ship where, he is liable to fall a distance of more than 2 m. or into water in which there is a risk of drowning.
(ii) Any young person under the age of sixteen shall, when employed in the operations in shipyard, be placed under the charge of an experienced workman.
(66) Safety supervisions - In the case of every shipyard other than a dry deck available for hire being a shipyard where the number of workers regularly or from time to time exceeds five hundred, a person experienced in the work of such yards shall be appointed and employed exclusively to exercise general supervision of the observance of this rule and to promote the safe conduct of the work generally.
127
61-J.Reaction Vessels and Kettles
This rule applies to reaction and kettles (hereinafter in this rule referred to as reaction vessels) which normally work at a pressure not above the atmospheric pressure, but in which there is likelihood of pressure being created above the atmospheric pressure due to reaction get-ting out at control or any other circumstances.
In the event of the vessel being heated by electrical means, a suitable control device shall be provided to prevent the temperature exceeding the safe limit.
Where steam is used for heating purposes in reaction vessel it shall be supplied through a suitable pressure reducing valve, (sic.) any other suitable automatic device to prevent the maximum permissible steam pressure being exceeded, unless the pressure of the steam in the supply line itself cannot exceed the said maximum permissible pressure.
A suitable safety valve or rupture disc of adequate size and capacity shall be provided to effectively, prevent the pressure being built up in the reaction vessel beyond the safe limit. Effective arrangements shall be made to ensure that the released gases, fumes, vapors, liquids or dusts, as the case may be, are led away and disposed of through suitable pipes without causing any hazard. Where flammable gases or vapors are likely to be vented out from the vessel, the discharge end shall be provided with a flame arrestor.
Every reaction vessel shall be provided with a pressure gauge having the appropriate range.
In addition to the devices as mentioned in the fore-going provisions, means shall be provided for automatically stopping the feed into the vessel as soon as process conditions deviate from the normal limits to an extent which can be considered as dangerous.
Where necessary, an effective system for cooling, flooding or blanketing shall he provided, for the purpose of controlling the reaction and process conditions within the safe limits of temperature and pressure.
An automatic auditory and visual warning device shall be provided for clear warning whenever process conditions exceed the present limits. This device, wherever possible, shall be integrated with automatic process correction systems.
A notice pointing out the possible circumstances in which pressures above atmospheric pressure may be built up in the reaction vessel, the dangers involved and the precautions to be taken by the operators shall be displayed at a conspicuous place near the vessel.] 128
61-K.Examination of eye sight of certain workers
No person shall be employed to operate a crane, locomotive or fork lift truck or to give signals to crane or locomotive operator unless his eye sight and colour vision have been examined and declared fit by a qualified ophthalmologist to work whether with or without use of corrective glasses.
The eye sight and colour vision of the person employed as referred to in sub-rule (1) shall be examined at least once in every two years.
Any fee payable for an examination of a person under this rule and the cost of corrective glasses shall be paid by the occupier and shall not be recoverable from that person. 129
[The record of examination or re-examination carried out by the concerned ophthalmologist shall be produced on demand]] 130
61-L.Railways In factories
This rule shall apply to railways in the precincts of a factory which are not subject to Indian Railways Act, 1890 (Central Act IX of 1890).
Gateways - A Gateway through which a railway track passes shall not be used for the general passage of workers into or out of a factory.
Barriers and turn gates
(a) Where building or walls contain doors or gates which open to a railway track, a barrier about 1 meter high shall be fixed parallel to and about 60 c.m. away from the building or wall outside the opening and extending several feet beyond it at either end, so that any person passing out may become aware of an approaching train when his pace is checked at the barrier. If the traffic of the nearest track is all in one direction, the barrier shall be in the form of a ’ L ’ with the end of the short leg abutting on to the wall and the other end opening towards the approaching train.
(b) If the distance between wall and track cannot be made to accommodate such a barrier, the barrier or a turngate shall be placed at the inside of the opening.
(c) Where a footway passes close to a building or other obstruction as it approaches a railway track, a barrier or a turngate shall be fixed in such a manner that a person approaching the track is compelled to move away from the building or obstruction and thus obtain timely sight of an approaching locomotive or wagon.
Crowd
(a) Workers' pay-window, first-aid stations and other points where a crowd may collect shall not be placed near a railway track.
(b) At any time of the day when workers are starting or ending work, all railways traffic shall cease for not less than five minutes.
Locomotives
(a) No locomotive shall be used in shunting operations unless it is in good working order
(b) Every locomotive and tender shall be provided with efficient brakes, all of which shall be maintained in good working order. Brake shoes shall be examined at suitably fixed interval and those that are worn out replaced at once.
(c) Water-gauge glasses of every locomotive, whatever its boiler pressure, shall be protected with substantial glass or metal screens.
(d) Suitable steps and hand-holds shall be provided at the corners of the locomotive for the use of shunters.
(e) Every locomotive crane shall be provided with lifting and jacking pads at the four corners of the locomotive for assisting in re-railing operations.
(f) It shall be clearly indicated on every locomotive crane in English and in language understood by the majority of the workers in the factory, for what weight of load and at what radius the crane is safe.
Wagons
(a) Every wagon (and passenger coach, if any) shall be provided either with self- acting brakes capable of being applied continuously or with efficient hand brakes which shall be maintained, in good working order. The hand brakes shall be capable of being applied by a person on the ground and fitted with a device for retaining them in the applied position.
(b) No wagon shall be kept standing within 3 meters of any authorised crossing
(c) No wagon shall be moved with the help of crow bars or pinch bars.
Riding on locomotive, wagon or other rolling stock- No person shall be permitted to be upon (whether inside or out-side) any locomotive wagon or other rolling stock except where secure foot hold and hand hold are provided.
Attention to brakes and doors
(a) No locomotive. wagon or other rolling stock shall be kept standing unless its brakes are firmly applied and, where it is on a gradient, without sufficient number of properly constructed scotches placed firmly in position.
(b) No train shall be set in motion until shunting jamadar has satisfied himself that all wagon doors are securely fastened.
Projecting loads and cranes
(a) If the load on a wagon projects beyond its length, a guard or dummy-truck shall be used beneath the projection.
(b) No loco-crane shall travel without load unless the job is completely lowered and positioned in line with the track.
(c) When it is necessary for a loco-crane to travel with a load, the jib shall not be swung until the loco-crane has come to rest.
Loose shunting- Loose shunting shall be permitted only when it cannot be avoided. It shall never be performed on a wagon not accompanied by a man capable of applying and pinning down the brakes. A wagon not provided with brakes in good working order and capable of being easily pinned down shall not be loose-shunted, unless there is attached to it at least another wagon with such brakes. Loose shunting shall not be performed with, or against a wagon containing passengers, live-stock or explosives.
Fly-shunting- Fly shunting shall not be permitted on any factory railway.
The shunting jamadar
(a) Every locomotive or wagon in motion in a factory shall be in charge of a properly trained jamadar.
(b) Before authorizing a locomotive or wagons to be moved, the shunting jamadar shall satisfy himself that no person is under or in between or in front of the locomotive or wagons.
Hand signals- The hand signals used by the shunting jamadar by day and night shall be those prescribed by the shunting rules of railways, working under the Indian Railways Act, 1890 (Central Act IX of 1890).
Night work and fog
(a) In factories where persons work at night, no movement of locomotive, wagon or other rolling stock otherwise than by hand shall be permitted between sunset and sunrise unless the tracks and their vicinity are lighted on a scale of not less than 10 lux as measured at the horizontal plane at the ground level.
(b) In no circumstances shall any locomotive or train be moved between sunset and sunrise or at any time when there is fog, unless it carries a white head light and a red rear light.
Speed control
(a) A locomotive or train shall not be permitted to move at a speed greater than seven kilometers per hour.
(b) A train, locomotive, wagon or other rolling stock shall not be moved by mechanical or electrical power unless it is preceded at a distance of not less than 10 meters during the whole of its journey by a shunting jamadar. He shall be provided with signaling flags or lamp and whistle necessary for calling the attention of the driver.
Tracks
(a) The distance (i) between tracks and between tracks and buildings, blind walls or other structures and (iii) tracks and materials deposited on the ground shall be respectively not less than:
(aa) from centre to centre of parallel tracks, the overall width of the widest wagon of that gauge plus twice the width of the door of such a wagon when opened directly outwards plus 1 meter.
(bb) from a building or structure other than a loading platform to the centre of the nearest track, half the overall width of the widest wagon of that gauge, plus the width of its door when opened outwards plus 1.5 meters.
(cc) from material stacked or deposited alongside the track, on the ground or on a loading platform, to the centre of the nearest track, half the overall width of the widest wagon of that gauge, plus half the width of its door when opened directly outward, plus 1 meter.
(b) Sleepers of a track shall be in level with ground and at all crossings of the track width a road or walkway, the surface of the road or walkway shall be in level with the top of the rails.
(c) All track ends shall be equipped with buffer stops of adequate strength.
(d) Barriers of substantial construction shall be securely and permanently fixed across any doorway or gateway in a building or in a wall which conceals an approaching train from view, between the building and the track as prescribed in clause (a) of sub-rule (3).
(e) Where tracks are carried on a gantry, or other elevation, a safety footway or footways with hand rails and toe-boards shall be provided at all positions where persons work or pass on foot; and where there is an opening in the stage of an elevated fenced or the opening itself provided with a grill through which a person cannot fall.
(f) All point levels shall have their movements parallel to, not across, the direction of the track.
(g) All loading platforms which are more than 60 c.m. above the level of the ground on which the track is laid and more than 15 meters in length shall be provided with steps at interval not greater than 15 meters apart to enable the platform to be easily mounted from the track.
(h) Turn tables on plant railways shall be provided with locking devices which will prevent the tables from turning while locomotives or wagons are being run on or off the tables.
(i) Workers shall be prohibited from passing under, between or above railway wagons.
Crossings
(a) At all crossings of a track with a road of walkway, danger or crossing signs and wherever reasonably practicable, blinking lights or alarm lights shall be provided. At all important crossings, gates or barriers manned by watchman shall be provided. Swinging gates and barriers shall be secured against inadvertent opening or closing.
(b) All crossings, warning, signs, gates and barriers shall be illuminated during hours of darkness.
Duties of drivers and shunters - It shall be the duty of every driver of a locomotive or a shunter including a shunting jamadar, to report without delay to their superior any defect in permanent way locomotive or rolling stock.
Young persons not to be employed as drivers of locomotive or as shunters- No person who is under 18 years of age and no person who is not sufficiently competent and reliable shall be employed as a driver of locomotive or as a shunter.
The Chief Inspector may by an order in writing exempt a factory or part of it from all or any of the provisions of this rule to such extent and on such conditions as he deems necessary].
131 [61-M. Safety Committee
(1) In every factory
(a) Wherein two hundred and fifty or more workers are ordinarily employed; or
(b) which carries on any process or operation declared to be dangerous under Section 87 of the Act; or
(c) which carries on hazardous process as defined under Section 2 (oh) Of the Act; there shall be a Safety Committee.
(2) The representatives of the management of Safety Committee shall include
(a) A senior official, who by his position in the organization can contribute effectively to the functioning of the Committee, shall he the Chairman;
(b) A Safety Officer and a Factory Medical Officer, wherever available and the Safety Officer, in such a case shall be the Secretary of the Committee;
(c) A representative each from the production, maintenance and purchase departments.
(3) The Workers' representatives on this Committee shall be as equal to the number of representatives of the management, as elected by the workers.
(4) The tenure of the Committee shall be three years.
(5) Safety Committee shall meet as often as necessary but at least once in every quarter. The minutes of the meeting shall be recorded and produced to the Inspector on demand.
(6) Safety Committee shall have the right to be adequately and suitably informed of
(a) Potential safety and health hazards to which the workers may be exposed at work place.
(b) data on accidents as well as data resulting from surveillance of the working environment and of the health of workers exposed to hazardous substances so far as the factory is concerned:
Provided that the Committee undertakes to use the data on a confidential basis and solely to provide guidance and advice on measures to improve the working environment and the health and safely of the workers.
(7) Functions and duties of the Safety Committee shall include
(a) Assisting and co-operating with the management in achieving the aims and objectives outlined in the Health and Safety Policy of the Occupier.
(b) dealing with all matters concerning health, safety and environment and to arrive at practicable solutions to problems encountered;
(c) creating safety awareness amongst all workers;
(d) undertaking educational, training and promotional activities;
(e) discussing reports on safety, environmental and occupational health surveys, safely audits, risk assessment, emergency and disaster management plans and implementation of the recommendations made in the reports;
(f) carrying out health and safety surveys and identifying causes of accidents;
(g) looking into any complaint made on the likelihood of an imminent danger to the safety and health of the workers and suggesting corrective measures; and
(h) Reviewing the implementation of the recommendations made by it.
(8) Where owing to the size of the factory or any other reason, the functions referred to in sub-rule (7) cannot be effectively carried out by the Safety Committee, it may establish sub-committees as may be required to assist it] 132 [61-N. Quality of personal protective equipment All personal protective equipments provided to workers as required under any of the provisions of the Act or the rules shall have certification by Indian Standard Institute.] 133 [61-O. Protective equipment The Inspector may, having regard to the nature of the hazards involved in work and process carried out, order the Occupier or the Manager in writing to supply to the workers exposed to particular hazard any personal equipment as may be found necessary.] 134 [61-P. Thermic Fluid Heaters
(1) All heaters shall be of such construction that coils are removable for periodic cleaning, visual inspection and hydraulic test.
(2) Suitable arrangements shall be made for cooling the furnace effectively In case of power failure.
(3) Before restarting the furnace, it shall be effectively purged.
(4) Velocity of flow of the thermic fluid shall not be allowed to fall below the minimum recommended by the manufacturers while the heater is in operation.
(5) The thermic fluid shall be circulated in dosed circuit formation with an expansion- cum-decorator tank. This tank shall be located outside the shed where the heater is installed.
(6) Every heater shall be provided with a Photo-register actuated audio-visual alarm to indicate flame failure and automatic burner cut off.
(7) The stack temperature monitor-cum-controller with audio-Visual alarm shall be provided so as to warn the operator in case the outlet temperature exceeds the specified minimum.
(8) Where inspection doors are provided on the furnace they shall be inter-locked with the burner itself so that they cannot be opened until burner is shut off and furnace is cooled sufficiently.
(9) All heaters shall also be provided with the following safety devices:
(i) Level control in the expansion tank;
(ii) temperature control of thermic fluid;
(iii) Differential pressure switch on the outlet line of the heater tubes; and
(iv) temperature control device for the fuel oil supply to the burner.
(10) All devices mentioned in paragraph (9) shall have interlocking arrangement with burner so that in case of any predetermined limits being crossed the supply of fuel and air to burner shall automatically be cut-off.
(11) All safety interlocks when operated shall be indicated on the control panel of the heater by a suitable audio-visual alarm.
(12) Every heater unit shall be provided as a standard accessory an arrangement for stifling with low pressure steam or nitrogen for putting out the fire.
(13) Electric panel for the heater shall be located near the heater but not so close as to be exposed to spilling or leaking oil.
(14) The heater shall be located in a place partitioned off with fire proof material from other manufacturing activities.
(15) Explosion vent shall be so installed that release takes place at safe location.
(16) The heater coil shall be subjected to pressure test by competent person once atleast in every 12 months. The test pressure shall not be less than twice the operating pressure.
(17) If repairs are carried out to the coil, it shall be tested before taking it into use.
(18) The thermic fluid shall conform to the specifications prescribed by the manufacturers and shall be tested by competent person for suitability atleast once in every three months period. Such test shall include lest for acidity, suspended matter, ash contents, viscosity and flash point.
(19) Cleaning of internal surface of the heater or soot and check up of refractory surface on the inside shall be carried out every month or as often as required depending upon working conditions. The coils shall be removed and surface of the coils cleaned thoroughly once atleast in a period of silt months. The burner, nozzles, oil filters and pumps shall be cleaned once a week during the periods of use.
(20) A separate register containing the following information shall be maintained
(i) weekly checks carried out confirming the effectiveness of the interlock,
(ii) weekly checks confirming that all accessories are in good state of repairs, and
(iii) information regarding fuel oil temperature, pressure, thermic fluid inlet/outlet pressure and temperature, fuel gas temperature, recorded at four hourly interval.
The heater when in operation shall always be kept in charge of a trained operator)
61-Q.Site appraisal committee
The State Government may appoint a Senior Official of the Factories Inspectorate to be a member and also function as the Secretary of the Committee.
No member of the Site Appraisal Committee unless required to do so by a Court of Law, shall disclose otherwise than in connection with the purpose of Act, at any lime any infatuation relating to manufacturing or commercial business or any working process which may come to his knowledge during his tenure as a Member on this Committee.
Applications for appraisal of sites
(a) Applications for appraisal of sites in respect of the Factories covered under Section 2 (cb) of the Act shall be submitted to the Chairman of the Site Appraisal Committee.
(b) The application for site appraisal along with fifteen copies thereof shall be submitted in the form annexed to this rule. The Committee may dispense with furnishing information on any particular item in the Application Form if it considers the same to be not relevant to the application under consideration.
Function of the Committee:
(a) The Member Secretary shall arrange to register the applications received for appraisal of site in a separate register and acknowledge the same within a period of seven days.
(b) The Member Secretary shall fix up meeting in such a manner that all the applications received and registered are referred to the Committee within a period of one month from the date of their receipt.
(c) The Committee may adopt a procedure for its working keeping in view the need for expeditious disposal of applications.
(d) The Committee shall examine the application for appraisal of a site with reference to the prohibitions and restrictions on the location of industry and the carrying on of processes and operations in different areas as per the provisions of rule 5 of the Environment (Protection) Rules, 1986 framed under the Environment (Protection) Act, 1986 (Central Act 29 of 1986).
(e) The Committee may call for documents, examine experts, inspect the site if necessary and take other steps for formulating its views in regard to the suitability of the site.
(f) The application for Site Appraisal will be considered by the Committee after obtaining Letter of Intent by the applicant from the Ministry of Industries of Government of India before its conversion as Industrial Licence.
Format of Application to the Site Appraisal Committee 1. Name and address of the applicant 2. Site Ownership Data 2.1 Revenue details of site such as Survey No. Plot No. etc. 2.2 Whether the site is classified as forest and if so, whether approval by the Central Government under Section 5 of the Indian Forest Act, 1927 has been taken. 2.3 Whether the proposed site attracts the provisions of Section 3 (2) (v) of the Environment (Protection) Act, 1986 (Central Act 29 of 1986). If so the nature of the restrictions. 2.4 Local authority under whose jurisdiction the site is located.
3. Site Plan 3.1 Site Plan with clear identification of boundaries and total area proposed to be occupied and showing the following details nearby the proposed site.
(a) Historical monument, if any, in the vicinity
(b) Names of neighboring manufacturing units and human habitats, educational and training institutions, Petrol Installations, storages of LPG and other hazardous substances in the vicinity and their distances from the proposed unit.
(c) Water sources (rivers, streams, canals, dams, water filtration plants, etc.) in the vicinity.
(d) Nearest hospitals, fire stations, civil defense stations and Police Stations and their distances.
(e) High tension electrical transmission lines, pipe lines for water, oil, gas or sewerage, railway lines, roads, stations, jetties and other similar installations.
3.2 Details of soil conditions and depth at which hard strata obtained.
3.3 Contour map of the area showing nearby hillocks and differences in levels 3.4 Plot Plan of the factory showing the entry and exit points roads within water drains, etc.
4. Project Reports 4.1 A summary of the salient features of the project 4.2 Status of the organization (Government, Semi-Government, Public or Private, etc.) 4.3 Maximum number of persons likely to be working in the factory 4.4 Maximum amount of power and water requirements and source of their supply 4.5 Block diagram of the buildings and installations in the proposed supply. 4.6 Details of housing colony, hospital, school and other infrastructural facilities proposed.
5. Organizations structure of the proposed manufacturing unit/factory 5.1 Organization diagrams of Proposed enterprise in general Health, Safety and Environment Protection Departments and their linkage to operation and technical departments 5.2 Proposed Health and Safety Policy 5.3 Area allocated for treatment of wastes and effluent 5.4 Percentage outlay on safety, health and environment protection measures 6. Meteorological data relating to the Site: 6.1 Average, minimum and maximum of Temperature Humidity Wind velocities During the previous ten years 6.2 Seasonal variations of wind directions 6.3 Highest water level reached during the floods in the area recorded so far 6.4 Lightening and seismic data of the area 7. Communication Links 7.1 Availability of telephone/telex/wireless and other communication facilities for outside communication 7.2 Internal Communication facilities proposed 8. Manufacturing Process Information 8.1 Process flow diagram 8.2 Brief write up on process and technology 8.3 Critical process parameters such as pressure build-up temperature rise and run-away reactions 8.4 Other external effects critical to the process having safety implications, such as in grass of moisture or water, contact with incompatible substances, sudden power failure. 8.5 Highlights of the built-in safety/pollution control devices or measures incorporated in the manufacturing technology 9. Information of Hazardous Materials 9.1 Raw materials, intermediates, products and by-products and their quantities (enclose Material Safety Data Sheet in respect of each hazardous substance). 9.2 Main and intermediate storages proposed for raw materials intermediate/products /by-products (maximum quantities to be stored at any time). 9.3 Transportation methods to be used for materials in. flow and outflow, their quantities and likely routes to be followed 9.4 Safety measures proposed for ---Handling materials ---internal and external transportation ---disposal (packing and forwarding of finished products) 10. Information on Dispersal/Disposal of wastes and Pollutants 10.1 Major pollutants (gas, liquid, solid) their characteristics and quantities (average at peak loads) 10.2 Quality and quantity of solid wastes generated, method of their treatment and disposal 10.3 Air, Water and Soil Pollution problems anticipated and the proposed measures to control the same, including treatment and disposal of effluents.] 135 11. [Process Hazard Information]. 11.1 Enclose a copy of the report on environmental impact assessment 11.2 Enclose a copy of the report on Risk Assessment Study. 11.3 Published (open or classified) reports, if any, on accident situations/occupational health hazards or similar plants elsewhere (within or outside the country).
12. Information of proposed safety and Occupational Health Measures 12.1 Details of fire fighting facilities and minimum quantity of water, CO2 and or other fire-fighting measures needed to meet the emergencies. 12.2 Details of In-house medical facilities proposed.
13. Information on Emergency Preparedness. 13.1 On-site emergency plan. 13.2 Proposed arrangements, if any, for mutual aid scheme with the group of neighboring factories.
14. Any other relevant information.
I certify that the information furnished above is correct to the best of my knowledge and nothing of importance has been concealed while furnishing it. Name and Signature of the Applicant.] 136
61-R.Road Safety in Factory premises
Definitions-For the purpose of this Rule,
(a) "Authority" means registering authority under Motor Vehicles Act, 1988 (Central Act 59 of 1988);
(b) "Driver or operator" means a person authorized by the authority to drive or operate a vehicle;
(c) "Vehicles" means all types of vehicles including carriages registered or required to be registered under the Motor Vehicles Act, 1988 (Central Act 59 of 1988) and rules framed thereunder and used within the factory premises.
Construction and maintenance of roads and safety in driving
(a) Internal roads shall be soundly constructed, surfaced with good wearing material and properly maintained.
(b) Suitable dividers shall be provided where the width of road is 16 meters or more.
(c) All junctions, blind comers and railway crossings shall have necessary cautionary traffic signals displayed.
(d) The speed limit shall be displayed at conspicuous places such as entrance to the factory and at a distance of every 500 meters along the roads inside the factory premises.
(e) Parking places with clear marking shall be provided at convenient places inside the factory premises.
(f) It shall be ensured that,
(i) no vehicle is allowed or required to enter the factory premises unless it is duly registered with the authority;
(ii) no driver or operator is allowed or required to drive the vehicle inside the factory premises unless he holds a valid driving licence;
(iii) record of details of vehicle, driver or operator or persons accompanying the vehicle and other information such as TREM CARD, as found necessary is maintained;
(iv) entry of vehicles is restricted to the necessity of the workplace;
(v) no vehicle is loaded beyond its rated capacity: and
(vi) no person is allowed to park or stay or take rest under, between or above the vehicle.
(g) Proper traffic signals shall be displayed at sharp turns or ' U ' turns or wherever necessary
(h) All traffic signals, markings and cautionary notices shall be displayed in Tamil.
(i) At blind corners, convex mirror shall be installed at correct angle which shall reflect the movement of any incoming vehicle to unwary pedestrian or another vehicle.
(j) While reversing the vehicle, it shall be ensured that suitable warning is sounded and if need be another person is deployed to give signals and clearance to the driver)
