The Tamil Nadu Factories Rules, 1950
Arrangement of Rules
G.O. No. 1041 of 1950 · Tamil Nadu · 68 chapters and schedules, 167 rules
SCHEDULE X
SCHEDULE X
PAPER, PAPER BOARD AND CORRESPONDING MACHINES FOR PULP PRODUCTION
1. Application
The requirements of the Schedule shall apply to machinery in manufacture of paper, paper board and also to the corresponding machines for pulp production.
2. Definitions
For the purpose of this schedule:
(a) "approach safety stop" means a safety device which automatically removes a hazardous function when part of a body comes within dangerous proximity of the danger zone;
(b) "broke " means paper or paper board wasted out during processing
(c) " broke Guilletine " means a machine with a straight knife for cutting up broke or paper reels;
(d) "Calendar "means a machine for glazing paper or paper board:
(e) " Calendar work platform " means a lifting platform at a Calendar;
(f) "Constant Pressure Switch" means a start and stop switch automatically returning to the stop position when not actuated:
(g) "Crosscutting knife" means a knife mounted on a cylinder roll cross cutting the web;
(h) "drum reel up" means a machine (pope reel) for reeling up the web on an empty spool, friction-driven
(i) "nip point " means roll nip or any other place where face converge or run so close together that part of the body is in danger of being caught and injured;
(j) "pulper " means a machine for making fiber suspension by mechanical treatment of pulp or paper broke;
(k) "reeling Drum or Spool" means a roll for reeling up the web in full machine width at the drum reel-up;
(l) "threading" means (ceding a narrower pointed web (tail end) through a machine;
(m) “ web" means pulp paper or paper-board in the shape of a continuous carpet during manufacturing or processing.
3. Safety Measures against Nip Hazards
(1) General: Nip points shall, when possible be inaccessible from floor level or from any other surface that can easily be stepped on. If this requirement cannot be satisfied the risk must be avoided in some other way, like air jet/chute, carrier ropes, carrier belt or felt. The platforms should have the board of atleast 100 millimeters high and two handrails al a height of 400 millimeters and at 900 millimeters. The vertical members of the platform should be spaced at 1 meter for cross platform and 2 meters for longitudinal platform.
(2) Threading: Threading shall be done without manual interference when feasible. If threading must be done manually measures must be taken to achieve adequate safety as in paragraph (I) above.
4. Reeling Drum Exchange
Feeding during spool exchange at the drum reel up shall be effected only by using air jet or air hose, if the speed of the paper machine exceeds 100 meters per minute. If the speed of the machine is less than 100 meters per minute the feeding may be done manually, but measures must be taken to safety during the operation.
5. Safety measures against risks of being squeezed or knocked down
The movement of machine pan or other technical device must not expose anybody to the risk of being squeezed, knocked down or injured. If it cannot be ensured that the danger- zone is in accession when a risk is present, the moving device must be equipped with an approach safety stop. Its movement controlled by a hand-operated constant pressure switch or the risk avoided.
6. Web Reeling
(1) Web reeling shall be arranged so that the reel cannot cause injury by moving without control from its intended position by providing a cradle or a protection barrier.
(2) When a reel is carried by a through shaft, a device must. if necessary, be arranged to keep the shaft ends in their intended position.
(3) When a reel is carried and substantially governed by resting on two rolls, an ejection shield must be arranged to stop any reel, ejection when the web speed exceeds 15 meters per minute. If the shield is movable. a web speed exceeding 15 meters per minute must not be attainable unless the shield is in its protective position. The shield must not be removable from that position if the web speed exceeds the above value.
7. Handling of reels
(1) A reel must not be automatically put in free motion on a floor level or surface that can easily be stepped on unless this can be done with adequate safety.
(2) A reel discharger shall be arranged and handled so that no-body can be injured by its function or by the discharge reel.
(3) The discharger must not come into operation unless measures are taken to receive the discharger reel safety, if necessary, the discharger shall be controlled by a hand- operated constant pressure switch from a place where the operator can supervise both the zone of movement of the discharger and the course of the discharged reel.
(4) A reel lifted by the ends of a through shaft must not rotate unless the shaft ends and the lifting equipment can stand the stress caused by the rotation.
8. Cutting of paper
(1) A power-driven sharp edged tool for cutting paper shall be shielded against inadvertent contact and as far as possible, inaccessible while in operation.
(2) A crosscutting knife shall be shielded so that the tool is inaccessible when in operation. It must not be possible to start the tool unless the shield is in its protective position and it must not be possible to open the shield unless the tool is inoperative and its energy supply has been cut off by a safety switch which can be locked in its off-position.
9. Pulpers, pulp chests. Etc
(1) The opening of a pulper, a pulp chest another reservoir of a feeding service shall be arranged so that nobody is in danger of falling or stepping down through the opening.
(2) A pulper and its feeding device shall have a joint emergency stop and if possible a joint energy cut-off device, lock able in the off position.
(3) Broke holes should not be allowed to become covered by paper or broke which may hide them from operating personnel.
10. Certain devices moving vertically
(1) Calendar work platforms, pallet table, rider rolls, ejection shields, reel lowering devices, lids o driving section covers broke guillotine knives or other stationery devices, which for functional reasons arc regularly maneuvered to considerably different heights. shall be constructed, handled and maintained in such a way that they do not cause any risk of injury by falling down or in any other way and must not be liable to fall down as a result of interruption or variation in the energy supply.
(2) An operating movement that can cause risk of injury shall be controlled by a constant pressure switch from a place where the operator can supervise the zone of movement.
(3) A device as referred to in paragraph (I) above carried by a wire rope or chain shall have the requisite derailment protection and a breaker to stop the movement if the wire rope or chain should slacken or burst.
(4) If operationally stopped in a position where it could cause a risk of injury by falling down, the device shall be automatically secured.
(5) The hoisting equipment of a device as referred to in paragraph (1) above shall be readily available for full inspection,
11. Calendar Work Platform
(1) Calendar work platform shall be longer than the width of the calendar roll and provided with a gate or opening bar. The gate may only be openable inward or the bar may only be openable upwards and it must not be capable of staying open. The bar shall contain at least two rails.
(2) A calendar super work platform shall be controlled by a constant pressure switch, located on the platform.
(3) Along the work side of the platform there shall be on emergency stop controlling the movement of the platform as well as the calendar bowl rotation.
(4) The hoisting and lowering speed must not exceed 0.15 meter per second.
(5) A hydraulic cylinder being part of the hoisting gear of a calendar work platform shall have a valve which, in the event of a hose or pipe fracture or considerable leakage. Prevents the platform from moving downwards or retards its descent. Such a valve shall be mounted in or directly on the cylinder.
(6) A calendar super work platform carried by wire rope or chain shall have a reliable catch.
(7) An elevating screw of a calendar wait platform shall be self broking bearing nuts and safety nuts shall serve as load-carrying devices.
12. Examination and Inspection
(1) A device as referred to in paragraph 10 (1) above, shall when needed and atleast twice a year, and in case of a calendar work platform once a month, is subjected to thorough examination by a competent person as long as it is being used. If a calendar work platform has been out of use for more than three months, thorough examination shall be carried out before it is used again.
(2) In the course of examination, a check shall be made to ensure that safety devices are in working order and also that the hoisting and towering speed of the calendar work platform does not exceed the permitted value.
(3) An examination log book shall he maintained and made readily available.
13. Hose Pipes
(1) A hose pipe used for cleaning near a rotating pair of rolls shall have a rounded nozzle or otherwise be arranged so that the nozzle cannot be caught in the nip.
(2) A hose used for flushing liquid at a pressure exceeding 25 Kilogram/Centimeter shall have a constant pressure actuated valve for flow control. If needed for safely during handling the nozzle shall be mounted on a stand or the hose designed for two operators.
14. Space inside a machine
Any opening leading to a walkable passage into or through a machine must be blocked. This does not apply if the passage must be accessible for operational or maintenance purpose on condition that entering does not involve any risk.
15. Inching
If it is necessary, to operate a machine temporarily without the protective devices otherwise provided, the speed of the web shall be as low as possible and shall not exceed 15 meters per minute. The machine shall he governed by a hand operated constant pressure switch from a place where the operator can supervise those places where protective devices have been rendered inoperative.
16. Emergency stop
An emergency stop must not break the energy supply to any device needed in an emergency or provoke any movement that might aggravate the situation. Braking provoked by the emergency stop must not be so violent as to cause any risk of injury.
17. Auxiliary measures
In place where large quantities of pulp or broke are frequently handled, measures shall he taken to facilitate the work. Special attention shall he paid to the need for such measures in places where there are high temperatures.
18. Work Instructions
(1) Instructions shall be provided for the work routines necessary to promote safety during normal operation as well as during maintenance cleaning supervision and similar kinds of periodically recurrent tasks.
(2) Work permit system should be adopted for maintenance and cleaning operations.
19. Other Safety Precautions
(1) Wherever risk of injury prevails, necessary caution boards or symbols should be displayed like moving equipments, Nip points, slippery area, men at work, etc.
(2) Adequate training in safe operations should be imparted to workers at the time of induction into the factory and at periodical intervals not exceeding a year and whenever there is a job rotation or operational changes.
(3) For paper machine speeds exceeding 200 meters per minute start up alarm should be provided before crawl and before being put to run.
(4) All rotating elements should indicate direction of rotation.
(5) Wherever nip is there, indication in bold letter to be provided.)
