The Tamil Nadu Factories Rules, 1950
Arrangement of Rules
G.O. No. 1041 of 1950 · Tamil Nadu · 68 chapters and schedules, 167 rules
SCHEDULE to rule 102-A
SCHEDULE
1. Definitions
For the purpose of this schedule
(a) " mg/m3 " means milligrams of a substance per cubic meter of air;
(b) "mppcm" means million particles of a substance per cubic meter of air;
(c) "ppm" means parts of vapour or gas per million parts of air by volume at 250C and 760mm of mercury pressure;
(d) "Time weighted average concentration" means the average concentration of a substance in the air at any work location in a factory computed from evaluation of adequate number of air samples taken at that location spread over the entire shift on an day, after giving weightage to the duration for which each such sample is collected and the concentration prevailing at the time of taking the sample. T ime w eig h t ed avera ge c on c e n t ra t i on = [(C 1 T 1+ C 2 T 2+ …. + C n T n) / 1 +T 2+ … T n] Where C1 represents the concentration of the substance for duration T1 (in hours); C2 represents the concentration of the substance for duration T2 (in hours); and Cn represents the concentration of the substance for duration Tn (in hours);
(e) " Work location " means a location in a factory at which a worker works or may be required to work at any time during any shift on any day.
2. Limits of concentrations of substance at work locations
(1) The time weighted average concentration of any substance listed in Table 1 or 2 of the schedule, at any work location in a factory during any shift on any day shall not exceed the limit of the permissible time weighted average concentration specified in respect of that substance:
Provided that in the case of a substance mentioned in Table 1 in respect of which a limit in terms of short term maximum concentration is indicated, the concentration of such a substance may exceed the permissible limit of the time weighted average concentration for the substance for short periods not exceeding 15 minutes at a time, subject to the condition that
(a) such periods during which the concentration exceeds the prescribed time weighted average concentration are restricted to not more than 4 per shift;
(b) the time interval between any two such periods of higher exposure >hail not be less than 60 minutes; and
(c) at no time the concentration of the substance in the air shall exceed the limit of short term maximum concentration.
(2) In the case of any substance given in Table 3, the concentration of the substance at any work location in a factory at any time during any day shall not exceed the limit of exposure for that substance specified in the Table.
(3) In the cases where the word " skin" has been indicated against certain substance mentioned in Tables 1 and 3, appropriate measures shall be taken to prevent absorption through cutaneous routes particularly skin, mucous membranes and eyes as the limits specified in these Tables are for conditions where the exposure is only through respiratory tract.
(4)
(a) In case, the air at any work location contains a mixture of such substances mentioned in Tables 1, 2 or 3, which have similar toxic properties, the time weighted concentration of each of these substances during the shift should be such, that when these time weighted concentration divided by the respective permissible time weighted average concentration specified in the abovementioned tables, and the fractions obtained are added together, the total shall not exceed unity, i.e. C /L +C /L + C n /L n should not exceed unity when When CI, C2, ….,Cn are the time weighted concentration of toxic substances 1,2 and in respectively, determined after measurement at work location; and LI, L2 Ln are the permissible time weighted average concentration of the toxic substances 1, 2...... and in respectively.
(b) In case the air at any work location contains a mixture of substances mentioned in Table 1, 2 or 3, and these do not have similar toxic properties, then the time weighted concentration of each of these substances shall not exceed the permissible time weighted average concentration specified in the above mentioned tables, for that particular substance.
(c) The requirements in clauses (a) and (b) shall be in addition to the requirements in paragraphs 2 (1) and (2).
3. Sampling and evaluation procedures
(1) Notwithstanding provisions in any other paragraphs, the sampling and evaluation procedures to be adopted for checking compliance with the provisions in the schedule shall be as per standard procedures in vogue from time to time.
(2) Notwithstanding the provisions in paragraph 5, the following conditions regarding the sampling and evaluation procedure to be adopted checking compliance with the provision in this schedule are specified.
(a) For determination of the number of particles per cubic meter in item 1 (a) (i)
(1) in Table 2, samples are to be collected by standard or midget impringer and the counts made by light field technique.
(b) The percentage of quartz in the 3 formulae given in item 1 (A) (i) of Table 2 is to be determined from airborne samples.
(c) For determination of number of fibers as specified in item 2(A) of Table 2, the membrance filter method [at 430 x magnification (4 mm objective) with phase contrast illumination] should be used.
(d) Both for determination of concentration and percentage of quartz for use of the formula given in item 1 (a) (i) (2) of Table 2, the fraction passing through a size selector with the following characteristics should only be considered. Aerodynamic diameter Percentage allowed by (Unity density sphere) size-selector 2.0 20 2.5 75 3.5 50 5.0 25 10.0 0
4. Power to require assessment of concentration of substances
(1) An Inspector may, by an order in writing, direct the occupier or manager of a factory to get before any specified date the assessment of the time weighted average concentration at any work location of any of the substances mentioned in tables 1, 2 or 3 carried out.
(2) The results of such assessment as well as the method followed for air sampling and analysis for such assessment shad be sent to the Inspector within three days from the date of completion of such assessment and also a record of the same kept readily available for inspection by an Inspector
5. Exemption
If in respect of any factory or a part of a factory, the Chief Inspector is satisfied: that, by virtue of the pattern of working time of the workers at different work locations or on account of other circumstances, no worker is exposed, in the air at the work locations, to a substance or substances specified in Tables I, 2 or 3 to such an extent as is likely to be injurious to his health, he (the Chief inspector) may by an order in writing, exempt the factory or a part of the factory from the requirements in paragraph 2, subject to such conditions, if any, as he may Specify therein. 266 [TABLE 1 Permissible limits of exposure Time weighted Short term maximum concentration Sl.No Substances average concentration (STEL)
(TWA) (8 hrs) (15 min).*
| ppm | Mg/m3** | ppm | Mg/m3** | ||
| (1) | (2) | (3) | (4) | (5) | (6) |
| 1 | Acetaldehyde | 100 | 180 | 150 | 270 |
| 2 | Acetic acid | 10 | 25 | 15 | 37 |
| 3 | Acetone | 750 | 1,780 | 1,000 | 2,375 |
| 4 | Acrolein | 0.1 | 0.25 | 0.3 | 0.8 |
| 5 | Acrylonitrile-skin (S.C) | 2 | 4.5 | - | - |
| 6 | Aldrin-skin | - | 0.25 | - | - |
| 7 | Allyl Chloride | 1 | 3 | 2 | 6 |
| 8 | Ammonia | 25 | 18 | 35 | 27 |
| 9 | Anilline-skin | 2 | 10 | - | - |
| 10 | Anisidine (o,p-isomers)-Skin | 0.1 | 0.5 | - | - |
Arsenic & soluble compounds (as
11 - 0.2 - -
As)
12 Benzene (HC) 0.5 1.5 25 7.5
Beryllium & compounds (as Be)
13 - 0.002 - -
(S.C.)
| 14 | Boron trifluoride-C | 1 | 3 | - | - |
| 15 | Bromine | 0.1 | 0.7 | 0.3 | 2 |
| 16 | Butane | 800 | 1,900 | - | - |
2-Butanone (Methyl ethyl Ketone-
17 200 590 300 885
MEK)
| 18 | n-Butyl acetate | 150 | 710 | 200 | 950 |
| 19 | n-Butyl alcohol-Skin-C | 50 | 150 | - | - |
| 20 | Sec/Tert Butyl acetate | 200 | 950 | - | - |
| 21 | Butyl mercaptan | 0.5 | 1.5 | - | - |
| 22 | Cadmium Dusts and salts (as Cd) | - | 0.05 | - | - |
| 23 | Calcium Oxide | - | 2 | - | - |
| 24 | Carbaryl (Sevin) | - | 5 | - | - |
| 25 | Carbofuran (Furadan) | - | 0.1 | - | - |
| 26 | Carbon disulphide-Skin | 10 | 30 | - | - |
| 27 | Carbon Monoxide | 50 | 55 | 400 | 440 |
| 28 | Carbon tetrachloride-Skin(S.C) 5 | 30 | - | - | |
| 29 | Chlordane-Skin | - | 0.5 | - | 2 |
| 30 | Chlorine | 1 | 3 | 3 | 9 |
Chlorobenzence
31 75 350 - -
(Monochlorobenzene)
| 32 | Chloroform (S.C) | 10 | 50 | - | - |
| 33 | Bis (Chlororomethly) ether (H.C.) | 0.001 | 0.005 | - | - |
| 34 Chromic acid and chromates (as Cr) | - | 0.05 | - | - | |
| 35 | Chromous salts (as Cr) | - | 0.5 | - | - |
| 36 | Copper Fume | - | 0.2 | - | - |
| 37 | Cotton dust, raw | - | 0.2+ | - | - |
| 38 | Cresol, all isomers-Skin | 5 | 22 | - | - |
| 39 | Cyanides (as CN)-Skin | - | 5 | - | - |
| 40 | Cyanogen | 10 | 10 | - | - |
DDT (Dichlorodiphenyl
41 - 1 - -
trichloroethane)
| 42 | Demeton Skin | 0.01 | 0.1 | - | - |
| 43 | Diazinon Skin | - | 0.1 | - | - |
| 44 | Dibutyl phthalate | - | 5 | - | - |
| 45 | Dichlorvos (DDVP)-Skin | 0.1 | 1 | - | - |
| 46 | Dieldrin-Skin | - | 0.25 | - | - |
| 47 | Dinitrobenezene (all isomers)Skin | 0.15 | 1 | - | - |
| 48 | Dinitrotoluene-Skin | - | 1.5 | - | - |
| 49 | Diphenyl (Biphenyl) | 0.2 | 1.5 | - | - |
| 50 | Endosulfan (Thipdan)-Skin | - | 0.1 | - | - |
| 51 | Endrin-Skin | - | 0.1 | - | - |
| 52 | Ethyl acetate | 400 | 1,400 | - | - |
| 53 | Ethyl alcohol | 1,000 | 1,900 | - | - |
| 54 | Ethylamine | 10 | 18 | - | - |
| 55 | Flurorides (as F) | - | 2.5 | - | - |
| 56 | Fluorine | 1 | 2 | 2 | 4 |
| 57 | Formaldehyde (S.C) | 1.0 | 1.5 | 2 | 3 |
| 58 | Formic acid | 5 | 9 | - | - |
| 59 | Gasoline | 300 | 900 | 500 | 1,500 |
| 60 | Hydrazine-Skin(S.C) | 0.1 | 0.1 | - | - |
| 61 | Hydrogen Chloride-C | 5 | 7 | - | - |
| 62 | Hydrogen cyanide Skin C | 10 | 10 | - | - |
| 63 | Hydrogen Fluoride (as F)-C | 3 | 2.5 | - | - |
| 64 | Hydrogen peroxide | 1 | 1.5 | - | - |
| 65 | Hydrogen sulphide | 10 | 14 | 15 | 21 |
| 66 | Iodine C | 0.1 | 1 | - | - |
| 67 | Iron Oxide Fume (F e 2O) (as Fe) | - | 5 | - | - |
| 68 | Isoamyl acetate | 100 | 525 | - | - |
| 69 | Isomyl alchohol | 100 | 360 | 125 | 450 |
| 70 | Isobutyl alcohol | 50 | 150 | - | - |
| 71 | Lead, inorg dusts and fumes (asPb) | - | 0.15 | - | - |
| 72 | Lindane-Skin | - | 0.5 | - | - |
| 73 | Malathion – Skin | - | 10 | - | - |
Manganese (as Mn) dust and
74 - 5 - -
compounds-C
75 Manganese fume (as Mn) - 1 - 3
Mercury (as Hg)-Skin
(i) Alkyl compounds - 0.01 - 0.03
(ii) All forms except alkyl 76
- 0.05 - -
vapour
(iii) Aryl and inorganic
- 0.1 - -
compounds
77 Methyl alcohol (Methanol)-Skin 200 260 350 310
Methyl cellosolve (2-
78 5 16 - -
Methoxyethanol)-Skin
| 79 | Methyl isobutyl ketone | 50 | 205 | 75 | 300 |
| 80 | Methyl isocyanate-Skin | 0.02 | 0.05 | - | - |
| 81 | Nephthalene | 10 | 50 | 15 | 75 |
| 82 | Nickel carbonyl (as Ni) | 0.05 | 0.35 | - | - |
| 83 | Nitric acid | 2 | 5 | 5 | 10 |
| 84 | Nitric oxide | 25 | 30 | - | - |
| 85 | Nitrobenzene-Skin | 1 | 5 | - | - |
| 86 | Nitrogen dioxide | 3 | 6 | 5 | 10 |
| 87 | Oil mist mineral | - | 5 | - | 10 |
| 88 | Ozone | 0.1 | 0.2 | 0.3 | 0.6 |
| 89 | Parathion skin | - | 0.1 | - | - |
| 90 | Phenol-skin | 5 | 19 | - | - |
| 91 | Phorate (Thimet)-Skin | - | 0.05 | - | 0.2 |
| 92 | Phosgene (Carbonyl chloride) | 0.1 | 0.05 | - | 0.2 |
| 93 | Phosphine | 0.3 | 0.4 | 1 | 1 |
| 94 | Phosphoric acid | - | 1 | - | 3 |
| 95 | Phosphorous (yellow) | - | 0.1 | - | - |
| 96 | Phosphorous Pentechloride | 0.1 | 1 | - | - |
| 97 | Phosphorous trichloride | 0.2 | 1.5 | 0.5 | 3 |
| 98 | Picric acid – Skin | - | 0.1 | - | 0.3 |
| 99 | Phridine | 5 | 15 | - | - |
| 100 | Silane 9Silicon tetrahydride) | 5 | 7 | - | - |
| 101 | Sodium hydroxide-C | - | 2 | - | - |
| 102 Styrene, monomer (phenylethlene0 50 | 215 | 100 | 425 | ||
| 103 | Sulphur dioxide | 2 | 5 | 5 | 10 |
| 104 | Sulphur hexafluoride | 1,000 | 6,000 | - | - |
| 105 | Sulphuric acid | - | 1 | - | - |
| 106 | Tetraethyl lead (as Po)-Skin | - | 0.1 | - | - |
| 107 | Toluene (Toluol) | 100 | 375 | 150 | 560 |
| 108 | O-Toludine-Skin (S.C) | 2 | 9 | - | - |
| 109 | Tributyl Phosphate | 0.2 | 2.5 | - | - |
| 110 | Trichloroethylene | 50 | 270 | 200 | 1080 |
| 111 | Uranium, natural (as U) | - | 0.2 | - | 0.6 |
| 112 | Vinyl chloride 9H.C) | 5 | 10 | - | - |
| 113 | Welding fumes | - | 5 | - | - |
| 114 | Xylene (o-, m-, p-isomers) | 100 | 435 | 150 | 655 |
| 115 | Zinc Oxide | ||||
| (i) Fume | - | 5.0 | - | 10 | |
| (ii) Dust (Total dust) | - | 10.00 | - | - | |
| 116 | Zicronium compounds (as Zr0 | - | 5 | - | 10 |
ppm: Parts of vapour or gas per million parts of contaminated air by volume at 25 C and 760 (mm of mercury) mg/m: milligram of substance per cubic meter of air * Not more than 4 times a day with at least 60 min. interval between successive exposure **: mg/m = (Molecular weight X ppm)/24.45 Lint: free dust as measured by the vertical elutriator cotton-dust sampler C: denotes ceiling limit Skin: denotes potential contribution to the overall exposure by the cuteous route including mucous membrane and eye S.C: denotes suspected human carcinogens H.C: denotes confirmed human carcinogens] 267 [TABLE 2 Permissible time weighed average Substance concentration Silica, Si O
(a) Crystalline
(i) Quartz
(1) In terms of dust count (10600)/(%Quartz+10) mppcm
(2) In terms of respirable dust 10/(% respirable Quartz+2 mg/m
(3) In terms of total dust 30/ (% Quarts+3) mg/m
(ii) Cristobalite Half the limits given against quartz
(iii) Tridymite Half the limits given against quartz
(iv) Silica, fused Same limits as for quartz Same limit as in formula in item (2) given against quartz.
(v) Tripoli 10 mg/m, total dust
(b) Amorphous Silicates
[Asbestos (H.C) (a) Amosite 0.5 fiber/cc***
(b) Chrystolite 1.0 fiber/cc ***
(c) Crocidolite 0.2 fiber/cc ***
(i) For fier greater than 5 um in length and less than 5 um in breadth with length to breadth ration equal to or greater than 3:1
(ii) As determined by the membrane filter method at 400-450x magnification (4 mm objective) phase contrast illumination], Portland Cement 10 mg/m Total dust containing less than 1% quartz Coal Dust 2 mg/m, respirable dust fraction containing less than 5% quartz Mppcm = Million particles per cubic meter of air, based on impinge samples by light-field techniques *As determined by the membrane filter method at 400-450 x magnification (4mm objective) phase contrast illumination. Respirable Dust: Fraction passing a size-selector with the following characteristics Aerodynamic Diameter (um) % passing selector
(unit) (density sphere) 2 90 2.5 75 305 50 5.0 25 10 0.1
