The Tamil Nadu Factories Rules, 1950
Arrangement of Rules
G.O. No. 1041 of 1950 · Tamil Nadu · 68 chapters and schedules, 167 rules
SCHEDULE XXXII
OPERATIONS IN FOUNDARIES AND FURNACES
1. Application
Provisions of this schedule shall apply to all parts of factories where any of the following operations or process are carried on:
(a) The production of iron casting or, as the case may be, steel castings by casting in moulds made of sand, loam, moulding composition or other mixture of materials, or by shell moulding or by centrifugal casting and any process incidental to such production;
(b) the production of non-ferrous castings by casting metal in moulds made of sand, loam, metal, moulding composition or other material or mixture or materials, or by shell mouldings, die-casting (including pressure die-casting), centrifugal casting or continuous casting and any process incidental to such production;
(c) the melting and casting of non-ferrous metal land/or ferrous metal) for the production of ingots, billets, slabs or other similar products and the stripping thereof; but shall not apply with respect to
(i) any process with respect to the smelting and manufacture of lead and the Electric Accumulators;
(ii) any process for the purposes of a printing we; or
(iii) any smelting process in which metal is obtained by a reducing operation or any process incidental to such operation; or
(iv) the production of steel in the form of ingots; or
(v) any process in the course of the manufacture of solder or any process incidental to such manufacture; or
(vi) the melting and casting of lead or any lead-based alloy for the production of ingots, billets, slabs or other similar products or the stripping thereof, or any process incidental to such melting, casting or stripping.
2. Definition
For the purpose of this Schedule
(a) "approved respirator ” means a respirator of a type approved by the Chief Inspector;
(b) " Cupola or furnace " includes a receiver associated there with;
(c) "dressing or fettling operations "includes stripping and other removal of adherent sand, corers, runners, risers, flash and other surplus metal from a casting and the production of reasonably clean and smooth surface, but does not include
(i) the removal of metal from a casting when performed incidentally in connection with the machining or assembling of castings after they have been dressed or fettled, or
(ii) any operation which is a knockout operation within the meaning of this Schedule;
(d) "foundry" means those parts of a factory in which the production of iron or steel or non-ferrous castings (not being the production of pig iron or the production of steel in the form of ingots) is carried on by casting in moulds made of sand, loam, moulding composition or other mixture of materials, or by steel moulding or by centrifugal casting in metal moulds lined with sand, or die casting including pressure die castings, together with any part of the factory in which any of the following processes arc carried on as incidental processes in connection with and in the course of, such production, namely, the preparation and mixing of materials used in foundry process, the preparation of moulds and cores, knock-out operations and dressing or fettling operations;
(e) "knock-out operations" means all methods of removing castings from moulds and the following operations, when done in connection therewith, namely, stripping, coring out and the removal of runners and risers;
(f) "pouring aisle" means an aisle leading from a main gangway or directly from a cupola or furnace to where metal is poured into moulds.
(g) “ qualified supervisors ” means a person possessing a Bachelor ’ s Degree in Science or Diploma or Degree in Engineering with Certificate in ferrous/non-ferrous technology from any institution recognised by the Chief Inspector.
3. Prohibition of use of certain materials as parting materials
(1) A material shall not be used as a parting material if it is a material containing compounds of silica calculated as silica to the extent more than five per cent, by weight of the dry material:
Provided that this prohibition shall not prevent the following being used as a parting material if the material does not contain an admixture of any other silica:
(a) Zirconium silicate (zircon).
(b) Calcined china clay.
(c) Calcined aluminious fireclay.
(d) Sillimanite.
(e) Calcined or fused alumina.
(f) Olivine.
(g) Natural sand.
(2) Dust or other matter deposited from a fettling or blasting process shall not be used as a parting material or as a constituent in a parting material.
4. Arrangement and storage
For the purposes of promoting safety and cleanliness in workrooms, the following requirements shall be observed:
(a) moulding boxes, loam plates, ladles, patterns, pattern plates, frames, boards, box weights, and other heavy articles shall be so arranged and placed as to enable work to be carried on without unnecessary risk;
(b) suitable and conveniently accessible racks, bins or other receptacles shall be provided and used for the storage of other gear and tools;
(c) where there is bulk storage of sand, fuel, metal scrap or other materials or residues, suitable bins, bunkers or other receptacles shall be provided for the purpose of such storage.
5. Construction, Installation and Operation
(1) The precinct in which induction furnace is installed shall be of adequate strength and shall be segregated from the other parts of the factory in such a way so that minimum number of workers is exposed to the risk of any fire or explosion at any time;
(2) Furnace shed shall be well ventilated
(3) All the fitting and attachment of Induction furnace shall be of good construction, sound material and adequate strength;
(4) Adequate arrangements shall be made to avoid tilting of the ladles while transportation th
(5) Ladle shall not be filled with molten metal more than 3/4 of its volume to avoid spillage of molten metal while being carried by the crane;
(6) The refractory material of the induction furnace shall be strong at high temperature, resistant to thermal shock, chemically inert, low thermal conductivity and co- efficient of expansion and of adequate uniform thickness.
(7) The lining of the induction furnace shall be checked by qualified supervisor every week for any wear and tear and damage as per relevant Bureau of Indian Standards.
(8) Adequate precautions shall be taken during repair of induction furnace as per relevant bureau of Indian Standards.
6. Construction of floors
(1) Floors or indoor workplaces in which the processes are carried on, other than parts which are of sand, shall have an even surface of hard material.
(2) No part of the floor of any such indoor workplace shall be of sand except, where this is necessary by reason of the work done.
(3) All parts of the surface of the floor of any such indoor workplace which are of sand shall, so far as practicable, be maintained in an even and firm condition.
7. Means of escape
There shall be atleast two ways of escape with adequate width at opposite ends of the furnace platforms.
8. Display of Notice
Notice regarding non-use of water, etc. near induction furnace shall be displayed
9. Charging of scrap in Induction Furnace
(1) No scrap material with close cavities shall be charged in the induction furnace. Scrap to be charged shall be dry and shall not contain oil or any other liquid or moisture.
(2) No scrap material shall be fed into induction furnace unless it is thoroughly checked in the presence of qualified Supervisor.
(3) No closed container scrap shall be fed into the furnace unless it is cut into pieces. Such container shall be rendered safe by suitable means.
(4) No wet scrap material shall be charged into the induction furnace.
(5) Scrap received in the form of pressed bundle should be opened, sorted and only then fed into furnace.
10. Cleanliness of Indoor workplaces
(1) All accessible parts of the walls of every indoor workplace in which the processes are carried on and of everything affixed to those wall shall be effectively cleaned by a suitable method to a height of not less than 4.2 meters from the floor at least once in every period of fourteen months. A record of the carrying out of every such effective cleaning in pursuance of this paragraph including the date (which shall be not less than five months nor more than nine months after the last immediately preceding washing, cleaning or other treatment).
(2) Effective cleaning by a suitable method shall be carried out atleast once every working day of all accessible parts of the floor of every indoor workplace in which the processes arc carried on, other than pans which are of sand; and the parts which are of sand shall be kept in good order.
11. Manual operations Involving molten metal
(1) There shall be provided and properly maintained for all persons employed on manual operations involving molten metal with which they are liable to be splashed, a working space for that operation
(a) which is adequate for the safe performance of the work and
(b) which, so far as reasonably practicable, is kept free from obstruction.
(2) Any operation involving the carrying by hand of a container holding molten metal shall be performed on a floor all parts of which were any person walks while engaged in the operation shall be on the same level:
Provided that, where necessary to enable the operation to be per-formed without undue risk, nothing in this paragraph shall prevent the occasional or exceptional use of a working space on a different level from the floor, being a space provided with a safe means of access from the floor for any person while engaged in the operation.
12. Gangways and pouring aisles
(1) In every workroom to which this paragraph applies constructed, reconstructed or converted for use as such after the making of this schedule and, so far as reasonably practicable, in every other workroom to which this paragraph applies, sufficient and dearly defined main gangways shall be provided and properly maintained which
(a) shall have an even surface of hard material and shall, in particular, not be of sand or have on them more sand than is necessary to avoid risk of flying metal from accidental spillage;
(b) shall be kept, so far as reasonably practicable, free from obstruction;
(c) if not used for carrying molten metal, shall be atleast 920 millimeters in width;
(d) if used for carrying molten metal shall be
(i) Where truck ladles are used exclusively, atleast 600 millimeters wider than the overall width of the ladle;
(ii) Where hand shanks are carried by not more than two men, atleast 920 millimeters in width;
(iii) Where hand shanks are carried by more than two men, atleast 1.2 meters in width; and
(iv) Where used for simultaneous travel in both directions by men carrying hand shanks, atleast 1.8 meters in width.
(2) In workroom to which this paragraph applies constructed, reconstructed or converted for use as such after the making of this Schedule, sufficient and clearly defined pouring aisles shall be provided and properly maintained which
(a) shall have an even surface of hard material and shall, in particular, not be of sand or have on them more sand than is necessary to avoid risk of flying metal from accidental spillage;
(b) shall be kept so far as reasonably practicable free from obstruction;
(c) if molten metal is carried in hand ladles or bull ladles by not more than two men per ladle, shall be atleast 460 millimeters wide, but where any moulds alongside the aisle arc more than 510 millimeters above the floor of the aisle, the aisle shall be not less than 600 millimeters wide;
(d) if molten metal is carried in hand ladles or bull ladles by more than two men per ladle, shall be atleast 760 millimeters wide;
(e) if molten metal is carried in crane, trolley or truck ladles, shall be of a width adequate for the safe performance of the work.
(3) Requirements of sub-paragraphs (1) and (2) shall not apply to any workroom or part of a workroom if, by reason of the nature of the work done therein, the floor of that workroom or, as the case may be, that part of a workroom has to be of sand.
(4) In this paragraph "workroom to which this paragraph applies" means a part of a ferrous or non-ferrous foundry in which molten metal is transported or used, and a workroom to which this paragraph applies shall be deemed for the purposes of this paragraph to have been constructed, reconstructed or converted for use as such after the making of this schedule if the construction, reconstruction or conversion thereof was begun after the making of this Schedule.
13. Work near cupolas and furnaces
No person shall carry out any work within a distance of four meters from a vertical line passing through the delivery and of any spout of a cupola or furnace, being a spout used for delivering molten metal, or within a distance of 2.4 meters from a vertical line passing through the nearest part of any ladle which is in position at the end of such a spout, except in either case where it is necessary for the proper use or maintenance of a cupola or furnace that work should be carried out within that distance of that work is being carried out at such a time and under such conditions that there is no danger to the person carrying it out from molten metal which is being obtained from the cupola or furnace or is in a ladle in position at the end of the spout.
14. Dust and fumes
(1) Open coal, coke or wood fires shall not be used for heating or drying ladles inside a workroom unless adequate measures are taken to prevent, so far as practicable, fumes or other impurities from entering into or remaining in the atmosphere of the workroom.
(2) No open coal, coke or wood fires shall be used for drying moulds except in circumstances in which the use of such fires is un-avoidable.
(3) Mould stoves, core stoves and annealing furnaces shall be so designed, constructed, maintained and worked as to prevent, so far as practicable, offensive or injurious fumes from entering into any workroom during any period when a person is employed therein
(4) All knock-out operations shall be carried out
(a) In a separate part of the foundry suitably partitioned off, being a room or part in which, so far as reasonably practicable, effective and suitable local exhaust ventilation and a high standard of general ventilation are provided; or
(b) In an area of the foundry in which, so far as reasonably practicable, effective and suitable local exhaust ventilation is provided, or where compliance with this requirement is not reasonably practicable, a high standard of general ventilation is provided.
(5) All dressing or fettling operations shall be carried out
(a) in a separate room or in a separate part of the foundry suitably partitioned off; or
(b) in an area of the foundry set apart for the purpose; and shall, so far as reasonably practicable, be carried out with effective and suitable local exhaust ventilation or other equally effective means of suppressing dust, operating as near as possible to the point of origin of the dust.
15. Maintenance and examination of exhaust plant
(1) All ventilating plant used for the purpose of extracting, suppressing or controlling dust or fumes shall be properly maintained.
(2) All ventilation plant used for the purpose of extracting, suppressing or controlling dust or fumes shall be examined and inspected once every week by a responsible person. This shall be thoroughly examined and tested by a competent person atleast once in every period of twelve months; and particulars of the results of every such examination and test shall be entered in a register approved by the Chief Inspector of Factories which shall be kept readily available for inspection by an inspector. Any defect found on any such examination and test shall be immediately reported in writing by the person carrying out the examination and test to the Occupier or Manager of the Factory.
16. Protective equipment
(1) The occupier shall provide and maintain suitable protective equipment specified for the protection of workers,
(a) suitable gloves or other protection for the hands for workers engaged in handling any hot material likely to cause damage to the hands by burn, scald or scar, or in handling pig iron, rough castings or other articles likely to cause damage to the hands by cut or abrasion;
(b) approved respirators for workers carrying out any operations creating a heavy dust concentration which cannot be dispelled quickly and effectively by the existing ventilation arrangements.
(2) No respirator provided for the purposes of sub-paragraph (1) (b) has been worn by a person shall be worn by another person if it has not since been thoroughly cleaned and disinfected.
(3) Persons who for any of their time
(a) work at a spout of or attend to, a cupola or furnace in such circumstances that material there from may come into contact with the body, being material at such a temperature that its contact with the body would cause a burn; or
(b) are engaged in, or in assisting with, the pouring of molten metal; or
(c) carry by hand or move by manual power any ladle or mould containing molten metal; or
(d) are engaged in knocking-out operations involving material at such a temperature that its contact with the body would cause a burn; shall be provided with suitable footwear and gaiters which worn by them prevent, so far as reasonably practicable, risk of burns to his feet and ankles.
(4) Where appropriate, suitable screens shall be provided for protection against flying materials (including splashes of molten metal and sparks and chips thrown off in the course of any process).
(5) The occupier shall provide and maintain suitable accommodation for the storage and make adequate arrangements for cleaning and maintaining of the protective equipment supplied in pursuance of this paragraph.
(6) Every person shall make full and proper use of the equipment provided for his protection in pursuance of sub-paragraphs (1) and (4) and shall without delay report to the Occupier, Manager or other appropriate person any defect in, or loss of, the same.
(7) Workers working in the furnace/casting pit area shall be provided with cotton clothes. Safety shoes, leg guards, apron, face shield, hand gloves and safety helmet.
(8) Workers employed for segregation of scrap shall be provided with safety shoes and hand gloves
(9) Five retardant and heat retardant clothing shall be provided to all the workers working on platform of induction furnace
17. Training and Supervision
(1) All operations under this Schedule shall be carried out under the supervision of qualified supervisors at all times.
(2) Workers carrying out operations and maintenance activities in foundries and furnaces shall be adequately trained
18. Washing and bathing facilities
(1) There shall be provided and maintained in clean state and good repair for the use of all workers employed in the foundry,
(a) a wash place under cover with either
(i) a trough with impervious surface fitted with a waste pipe without plug, and of sufficient length to allow at least sixty centimeters for every 10 such persons employed at any one time and having a constant supply of dean water from taps or jets above the trough at intervals of not more than sixty centimeters; or
(ii) atleast one tap or stand pipe for every ten such persons employed at any one time, and having a constant supply of dean water, the tap or stand pipe being spaced not less than 1.2 meters apart; and
(b) not less than one-half of the total number of washing places provided under clause (a) shall be in the form of bathrooms;
(c) a sufficient supply of clean towels made of suitable material changed daily, with sufficient supply of nail brushes and soap.
(2) The facilities provided for the purposes of sub-paragraph (1) shall be placed in- charge of a responsible person or persons and maintained in a clean and orderly condition.
19. Disposal of dross and skimming
Dross and skimming ’ s removed from molten metal or taken from a furnace shall be placed forthwith in suitable receptacles.
20. Disposal of waste
Appropriate measures shall be taken for the disposal of all waste products from shell moulding (including waste burnt sand) as soon as reasonably practicable after the castings have been knocked-out.
21. Material and equipment left out of doors
All material and equipment left out of doors (including material and equipment so left only temporarily or occasionally) shall be so arranged and placed as to avoid unnecessary risk. There shall be safe means of access to all such material and equipment and, so far reasonably practicable, such access shall be by roadways or pathways or which shall be properly maintained. Such roadways or pathways shall have a firm and even surface and shall, so far as reasonably practicable be kept free from obstruction.
22. Medical facilities and records of examinations and tests
(1) The occupier of every factory to which the schedule applies, shall
(a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose employment shall be subject to the approval of the Chief Inspector of Factories; and
(b) Provide to the said medical practitioner all the necessary facilities for the purpose referred to in sub-paragraph (a);
(2) The record of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in a separate register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector.
23. Medical Examination by Certifying Surgeon
(1) Every worker employed in a foundry shall be examined by a Certifying Surgeon within fifteen days of his first employment. Such medical examination shall include pulmonary function tests and chest X- ray. No worker shall be allowed to work after fifteen days of his first employment in the factory, unless certified fit for such employment by the Certifying Surgeon.
(2) Every worker employed in the said processes shall be re- examined by a Certifying Surgeon at least once in every 12 months. Such examination shall, wherever the Certifying Surgeon considers appropriate, include all the tests as specified in sub- paragraph (1) except chest X-ray which will be once in three years.
(3) The Certifying Surgeon after examining a worker, shall issue a certificate of fitness in Form 27. The record of examination and re-examinations carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the Manager of the Factory. There cord of each examination carried out under sub- paragraphs (1) and (2) including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a Health Register in Form 17.
(4) The certificate of fitness and the health register shall be kept readily available for inspection by the Inspector.
(5) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said processes on the ground that continuance therein would involve special danger to the health of the worker, he shall make a record of his findings in the said certificate and the health register. The entry of his findings in those documents should also include the period for which he considers that the said person is unfit for work in the said processes. The person so suspended from the process, shall be provided with alternate placement facilities unless he is fully incapacitated in the opinion of the Certifying Surgeon, in which case the person affected shall be suitably rehabilitated.
(6) No person who has been found unfit to work as said in sub-paragraph (5) above shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes.
24. Exemption
If in respect of any factory, the Chief Inspector is satisfied that owing to the exceptional circumstances or infrequency of the processes or for any other reason, all or any of the provisions of this schedule is not necessary for protection of the workers in the factory, the Chief Inspector may by a Certificate in writing, which he may at his discretion revoke at any time, exempt such factory from all or any of such provisions subject to such conditions, if any, as he may specify therein.]
